Asbestos & Lead Based Paint Assessment City of Anderson 710 A&B Beechwood Avenue Anderson, South Carolina 29624

Transcription

1 Asbestos & Lead Based Paint Assessment City of Anderson 710 A&B Beechwood Avenue Anderson, South Carolina Prepared for: City of Anderson Community Development Department 601 South Main Street Anderson, South Carolina Prepared by: Apex Environmental Management, Inc. 7 Winchester Court Mauldin, South Carolina Project Number: March 4, 2015

2 Apex Project Number Winchester Court Mauldin, SC office fax SERVICES Indoor Air Quality Mold Remediation Asbestos & Lead Industrial Hygiene Worker Health & Safety Mold Consulting Moisture Management Plans Safety Assessment Environmental Site Assessments Hazard Communication Ms. Erica Craft City of Anderson Community Development Department 601 South Main Street Anderson, South Carolina Reference: Dear Ms. Craft: Asbestos and Lead-Based Paint Assessment Services 710 A&B Beechwood Avenue Anderson, South Carolina March 4, 2016 Apex Environmental Management, Inc. (Apex) is pleased to provide the results of our assessment services for the referenced property in accordance with Apex proposal number P dated November 10, This report and the associated attachments summarize our evaluation of the conditions observed at the project site. The findings presented by Apex are based upon sampling performed in the subject building. There is a chance that undetected ACM may exist in the building between walls or in other areas that would only be exposed during demolition or structural renovations. Should material be discovered that could potentially contain asbestos during the demolition process, additional samples of the material should be collected by a licensed asbestos inspector and submitted to an accredited laboratory for analytical interpretation. Our recommendations are based on the guidelines presented in EPA and/or OSHA regulations. Please note that this document is not a specification for asbestos removal. It does not contain means and methods for abatement. Quantities are estimates and contractors must verify amounts prior to bidding or removal. If you are planning an abatement project, please contact Apex to discuss the requirements. Use of this document without the express written consent of Apex is at the sole risk of the user and or/abatement contractor. The conclusions and/or recommendations contained in this report are based on our understanding of the applicable standards at the time this report was prepared. No warranty, expressed or implied, is made. If you have any questions please feel free to contact us at (864) Respectfully submitted, APEX ENVIRONMENTAL MANAGEMENT, INC. Thomas H. Oliver Director of Operations Tedman K. Shultz Project Manager Appendices

3 ASBESTOS AND LEAD BASED PAINT ASSESSMENT CITY OF ANDERSON 710 A&B BEECHWOOD AVENUE ANDERSON, SOUTH CAROLINA APEX PROJECT NO TABLE OF CONTENTS SECTION I II III IV V Asbestos & Lead Evaluation Report Asbestos & LBP Data Tables Laboratory Analytical Results Photographic Log SC DHEC Asbestos Inspector License

4 SECTION I Asbestos & Lead Evaluation Report

5 ASBESTOS/LEAD EVALUATION REPORT APEX PROJECT NUMBER: Date: 3/4/2016 Page Number: 1 of 4 Client: City of Anderson Client Contact: Ms. Erica Craft Client 601 South Main Street Client Phone (864) Address: Anderson, SC Number: Project: Property Address: Asbestos and Lead Evaluation 710 A&B Beechwood Ave. Anderson, SC Assessor: Ted Shultz Date of 2/18/2016 Assessment: Company: Apex Environmental Management 7 Winchester Court Mauldin, SC Phone Number (864) Purpose of Assessment: Demolition Age of Structure: 50 ± years Building Type: Residential Number of Stories: 1 Foundation: Brick & CMU Block Crawlspace Approximate Square Footage 1,800 SF EXTERIOR BUILDING MATERIALS Pitched wooden roof with shingles felt. Brick siding. Wooden windows. Window glazing. INTERIOR BUILDING MATERIALS Multiple types & layers of vinyl floor with no mastic. Plaster with texture & finish. Drywall with no joint compound & tape. Wooden floors. 1

6 City of Anderson 710 A&B Beechwood Avenue Apex Project No March 4, 2016 SCOPE OF THE SURVEY The objectives of the asbestos and lead assessment included the following: Identification of suspect asbestos-containing material (ACM) and lead based paints (LBP) in readily observable locations. Limited demolition of building finishes was conducted. Asbestos survey with sample collection by a South Carolina accredited inspector. Suspect ACM analysis by polarized light microscopy (PLM) utilizing CEI Labs (CEI) as an NVLAP certified laboratory, their accreditation number is Transmission electron microscopy (TEM) analysis of non-friable organically bound materials suspected to contain asbestos and testing negatively by PLM analysis. Lead inspection by a lead inspector certified by the Environmental Protection Agency and licensed to conduct LBP surveys in South Carolina. In situ analysis of suspected lead based paints by X-ray fluorescence (XRF). Presenting the results in a report identifying confirmed ACMs and LBPs. METHODS Asbestos Containing Materials In order to determine if the suspect materials observed during the visual survey contained asbestos, representative bulk samples were collected and placed in sealed packages. Twentysix (26) bulk samples were collected during the survey and submitted to CEI Labs (CEI) in Cary, North Carolina for analysis using the EPA recommended method of Polarized Light Microscopy (PLM) coupled with dispersion staining (Method No. EPA 600/M , Dec. 1982). CEI participates in the National Voluntary Laboratory Accreditation Program (NVLAP). Their NVLAP accreditation number is EPA regulations require that multiple samples of each homogeneous material be collected for laboratory analysis. In accordance with South Carolina Regulation , non-friable organically bound materials that are reported to be nonasbestos containing by PLM analysis must also be analyzed by Transmission Electron Microscopy (TEM). Ten (10) samples were analyzed using TEM. Lead-Based Paint Lead painted surfaces were analyzed in place using X-ray fluorescence. Painted surfaces were selected based on color of topcoat, underlying layers and substrate on which it was painted. RESULTS Asbestos Containing Materials The EPA defines an asbestos-containing material (ACM) as a material containing more than 1% asbestos. OSHA defines ACM as a material containing any amount of asbestos. Provided below is a general discussion of the asbestos containing materials identified in the residence. A specific PLM and TEM table is located in Appendix II of this report and identifies positive materials and designates approximate quantities. 2

7 City of Anderson 710 A&B Beechwood Avenue Apex Project No March 4, 2016 No materials sampled during the assessment were identified to be asbestos containing. Lead Based Paint OSHA does not recognize a threshold level of lead for definition purposes, only the presence or absence of lead. The current OSHA regulations recognize an airborne action level of thirty micrograms per cubic meter (30 µg/m 3 ) during an eight-hour workday and a permissible exposure level of fifty micrograms per cubic meter (50 µg/m 3 ) for employees. Currently, the EPA defines LBP as paint containing in excess of, or equal to, 1.0 mg/cm 3. The XRF analytical results and approximate locations of the paint samples collected are included in the Lead Analysis Report in Appendix II. Several surfaces in the building tested positive for lead in excess of the regulatory definition: Exterior White wooden door frames Interior No surfaces tested positive for LBP RECOMMENDATIONS AND DISCUSSION Asbestos Containing Materials No asbestos was present in the materials sampled within the structure. Therefore, no recommendations are necessary at this time. Lead-Based Paint 1. Currently the South Carolina Department of Health and Environmental Control (SCDHEC) define LBP as paint containing greater than 1.0 milligrams per square centimeter (mg/cm 2 ) lead or in excess of, or equal to, 0.5 percent lead. Building materials identified as being painted with LBP should be segregated from the other building materials and recycled or disposed of in a municipal lined landfill. The removed wastes would need to be containerized and further tested by Toxic Characteristic Leaching procedures (TCLP) to determine if the waste is classified as hazardous. The remaining building materials that are not painted with LBP may be disposed of in a construction and demolition landfill. However, the landfills should be contacted to determine their specific disposal requirements. 2. Occupational Safety and Health Administration Lead Regulations apply to actions initiated on lead containing materials. This regulation applies to lead concentrations greater than the analytical limit of detection. This regulation sets exposure levels on airborne lead and does not reference the percent lead in paint. Therefore, initial personal air monitoring should be conducted on workers performing work on surfaces which have a lead concentration of 0.1 mg/ cm 2 or above to satisfy the OSHA requirements. If a baseline exposure lower than the OSHA Action Level of 30 3

8 City of Anderson 710 A&B Beechwood Avenue Apex Project No March 4, 2016 micrograms per cubic meter ( g/m 3 ) is established, personal air monitoring may be terminated. The full OSHA lead standard should be referenced for compliance. This report summarizes our evaluation of the conditions observed at the site. The findings prepared by Apex are based upon testing performed in the structures. Our recommendations are based on the guidelines presented in EPA, State of South Carolina and OSHA asbestos regulations. Please note that this document is not a specification for asbestos or lead paint removal. It does not contain means and methods for asbestos or lead paint abatement. If you are planning an asbestos or lead paint abatement project, please contact Apex to discuss the requirements. Use of this document without the express written consent of Apex is at the sole risk of the user and/or abatement contractor. Quantities provided in this report are estimated. Contractors must verify material amounts prior to bidding or removal. This report summarizes our evaluation of the conditions observed at the site. The findings prepared by Apex are based upon testing performed in the building space. Additional ACM or LBP may exist (undetected) in other areas due to their inaccessibility or due to the limited nature of our testing. Our assessment procedures and recommendations are based on the guidelines presented in EPA, State of South Carolina or OSHA asbestos regulations. A copy of this report must be submitted to SCDHEC at least ten (10) working days prior to demolition when applying for a demolition permit. 4

9 SECTION II Asbestos & LBP Data Tables

10 ASBESTOS SURVEY PLM & TEM FIELD DATA SHEET Project Name: COA 700 A & B Beechwood Avenue ACM/LBP Sampled By: Ted Shultz Project Location: 700 A & B Beechwood Avenue, Anderson, SC Project Manager: Rebecca Shultz Project Number: Date: 2/18/2016 Sample No. Location Sample Description Analytical Results 1 12" x 12' self-stick floor tile & tan & 2 A & B kitchen with white square pattern vinyl floor PLM - NAD 3 with no mastic TEM - NAD 4 Multplie layers of tan, beige & white PLM - NAD 5 B bathroom vinyl floors with no mastic 6 TEM - NAD Throughout Throughout Plaster with texture & finish Drywall with no joint compound or tape PLM - NAD PLM - NAD Windows Window glazing PLM - NAD TEM - NAD Friable/Non Friable Condition Quantity Non-Friable G 300 SF Non-Friable G 40 SF Friable Damaged 4,500 SF Friable Damaged 4,500 SF Friable Damaged 8 EA

11 Sample No. Location Sample Description Analytical Results Roof Roof shingles (2 layers) & felt PLM - NAD 26 TEM - NAD NAD = No Asbestos Detected LF = Linear Feet EA = Each Bold = Positive For Asbestos SF = Square Feet Friable/Non Friable Condition Quantity Non-Friable Damaged 2,200 SF

12 FIELD DATA SHEET LBP ANALYSIS Project Name: COA 710 A & B Beechwood Avenue ACM/LBP Sampled By: Ted Shultz Project Location: 710 A & B Beechwood Avenue, Anderson, SC Project Manager: Rebecca Shultz Project Number: Date: 2/18/2016 Sample No. Sample Location Component Color Substrate Analytical Result (mg/m 3 ) 16 side porch post white wood side porch door frame white wood interior door frame white wood NA 19 interior door frame white wood interior wall white plaster interior book shelf white wood interior base board white wood NA 23 interior base board white wood interior window frame white wood interior door frame white wood 0.19 Bold = Positive for LBP in excess of 1.0 mg/cm2 NA = Insufficient Test Time

13 SECTION III Laboratory Analytical Results

14 February 24, 2016 Apex Environmental Management 7 Winchester Court Mauldin, SC CLIENT PROJECT: COA 710 Beechwood Ave CEI LAB CODE: B Dear Customer: Enclosed are asbestos analysis results for PLM Bulk samples received at our laboratory on February 19, The samples were analyzed for asbestos using polarizing light microscopy (PLM) per the EPA 600 Method. Sample results containing >1% asbestos are considered asbestos-containing materials (ACMs) per EPA regulatory requirements. The detection limit for the EPA 600 Method is <1% asbestos by weight as determined by visual estimation. Thank you for your business and we look forward to continuing good relations. If you have any questions, please feel free to call our office at Kind Regards, Tianbao Bai, Ph.D., CIH Laboratory Director 107 New Edition Court Cary, NC

15 ASBESTOS ANALYTICAL REPORT By: Polarized Light Microscopy Prepared for Apex Environmental Management CLIENT PROJECT: COA 710 Beechwood Ave CEI LAB CODE: B TEST METHOD: EPA 600 / R93 / 116 and EPA 600 / M4-82 / 020 REPORT DATE: 02/24/16 TOTAL SAMPLES ANALYZED: 22 # SAMPLES >1% ASBESTOS: TEL:

16 Asbestos Report Summary By: POLARIZING LIGHT MICROSCOPY PROJECT: COA 710 Beechwood Ave CEI LAB CODE: B METHOD: EPA 600 / R93 / 116 and EPA 600 / M4-82 / 020 Client ID Layer Lab ID Color Sample Description ASBESTOS % B147591A Tan,Patterned Floor Tile B147591B Clear Mastic B147591C Beige,Gray Sheet Vinyl B147592A Tan,Patterned Floor Tile B147592B Clear Mastic B147592C Beige,Gray Sheet Vinyl B Sample Submitted for TEM Analysis B147594A Tan,Gray Sheet Vinyl B147594B Beige,Gray Sheet Vinyl B147594C Off-white,Gray Sheet Vinyl B147595A Tan,Gray Sheet Vinyl B147595B Beige,Gray Sheet Vinyl B147595C Off-white,Gray Sheet Vinyl B Sample Submitted for TEM Analysis Layer 1 B White Texture Layer 2 B White Plaster Skim Coat Layer 3 B Gray Plaster Base Coat Layer 1 B White Texture Layer 2 B White Plaster Skim Coat Layer 3 B Gray Plaster Base Coat Layer 1 B White Texture Layer 2 B White Plaster Skim Coat Layer 3 B Gray Plaster Base Coat Layer 1 B White Texture Layer 2 B Gray Plaster Layer 1 B White Texture Layer 2 B White Plaster Skim Coat Layer 3 B Gray Plaster Base Coat Layer 1 B White Texture Layer 2 B White Plaster Skim Coat Page 1 of 2

17 Asbestos Report Summary By: POLARIZING LIGHT MICROSCOPY PROJECT: COA 710 Beechwood Ave CEI LAB CODE: B METHOD: EPA 600 / R93 / 116 and EPA 600 / M4-82 / 020 Client ID Layer Lab ID Color Sample Description ASBESTOS % Layer 3 B Gray Plaster Base Coat Layer 1 B White Texture Layer 2 B White Plaster Skim Coat Layer 3 B Gray Plaster Base Coat B Gray Drywall B Gray Drywall B Gray Drywall B Gray Drywall B Gray Drywall B Gray Drywall B Gray Drywall B White Window Glazing B White Window Glazing B Sample Submitted for TEM Analysis Layer 1 B Off-white,Black Roof Shingle Layer 2 B Black Roof Shingle Layer 3 B Black Felt Paper Layer 1 B Off-white,Black Roof Shingle Layer 2 B Black Roof Shingle Layer 3 B Black Felt Paper B Sample Submitted for TEM Analysis Page 2 of 2

18 ASBESTOS BULK ANALYSIS By: POLARIZING LIGHT MICROSCOPY Client: Apex Environmental Management 7 Winchester Court Mauldin, SC Project: COA 710 Beechwood Ave ASBESTOS BULK PLM, EPA 600 METHOD Client ID Lab ID Lab Description Lab Attributes NON-ASBESTOS COMPONENTS Non- ASBESTOS % 1 B147591A Floor Tile Tan,Patterned 100% Vinyl B147591B Mastic 100% Mastic Clear B147591C Sheet Vinyl 20% Beige,Gray Cellulose Fiberglass 50% 2 Vinyl 2 B147592A Floor Tile Tan,Patterned 100% Vinyl B147592B Mastic 100% Mastic Clear B147592C Sheet Vinyl 20% Beige,Gray Cellulose Fiberglass 50% 2 Vinyl 3 B Sample Submitted for TEM Analysis 4 B147594A Sheet Vinyl Tan,Gray 20% Cellulose Fiberglass 50% 2 Vinyl Page 1 of 8

19 ASBESTOS BULK ANALYSIS By: POLARIZING LIGHT MICROSCOPY Client: Apex Environmental Management 7 Winchester Court Mauldin, SC Project: COA 710 Beechwood Ave ASBESTOS BULK PLM, EPA 600 METHOD Client ID Lab ID Lab Description Lab Attributes NON-ASBESTOS COMPONENTS Non- ASBESTOS % B147594B Sheet Vinyl Beige,Gray 20% Cellulose Fiberglass 50% 2 Vinyl B147594C Sheet Vinyl Off-white,Gray 20% Cellulose Fiberglass 50% 2 Vinyl 5 B147595A Sheet Vinyl Tan,Gray 20% Cellulose Fiberglass 50% 2 Vinyl B147595B Sheet Vinyl Beige,Gray 20% Cellulose Fiberglass 50% 2 Vinyl B147595C Sheet Vinyl Off-white,Gray 20% Cellulose Fiberglass 50% 2 Vinyl 6 B Sample Submitted for TEM Analysis 7 Layer 1 B Texture White 10% Talc 80% Calc Carb Paint Layer 2 B Plaster Skim Coat White 6 30% Paint Page 2 of 8

20 ASBESTOS BULK ANALYSIS By: POLARIZING LIGHT MICROSCOPY Client: Apex Environmental Management 7 Winchester Court Mauldin, SC Project: COA 710 Beechwood Ave ASBESTOS BULK PLM, EPA 600 METHOD Client ID Lab ID Lab Description Lab Attributes NON-ASBESTOS COMPONENTS Non- ASBESTOS % Layer 3 B Plaster Base Coat Gray Layer 1 B Texture White 10% Talc 80% Calc Carb Paint Layer 2 B Plaster Skim Coat White 6 30% Paint Layer 3 B Plaster Base Coat Gray Layer 1 B Texture White 10% Talc 80% Calc Carb Paint Layer 2 B Plaster Skim Coat White 6 30% Paint Layer 3 B Plaster Base Coat Gray 3 6 Page 3 of 8

21 ASBESTOS BULK ANALYSIS By: POLARIZING LIGHT MICROSCOPY Client: Apex Environmental Management 7 Winchester Court Mauldin, SC Project: COA 710 Beechwood Ave ASBESTOS BULK PLM, EPA 600 METHOD Client ID Lab ID Lab Description Lab Attributes NON-ASBESTOS COMPONENTS Non- ASBESTOS % 10 Layer 1 B Texture White 10% Talc 80% Calc Carb Paint Layer 2 Plaster B Lab Notes: No skim coat present. Gray Layer 1 B Texture White 10% Talc 80% Calc Carb Paint Layer 2 B Plaster Skim Coat White 6 30% Paint Layer 3 B Plaster Base Coat Gray Layer 1 B Texture White 10% Talc 80% Calc Carb Paint Layer 2 B Plaster Skim Coat White 6 30% Paint Page 4 of 8

22 ASBESTOS BULK ANALYSIS By: POLARIZING LIGHT MICROSCOPY Client: Apex Environmental Management 7 Winchester Court Mauldin, SC Project: COA 710 Beechwood Ave ASBESTOS BULK PLM, EPA 600 METHOD Client ID Lab ID Lab Description Lab Attributes NON-ASBESTOS COMPONENTS Non- ASBESTOS % Layer 3 B Plaster Base Coat Gray Layer 1 B Texture White 10% Talc 80% Calc Carb Paint Layer 2 B Plaster Skim Coat White 6 30% Paint Layer 3 B Plaster Base Coat Gray B Drywall Gray 10% Cellulose 8 Gypsum 15 B Drywall Gray 10% Cellulose 8 Gypsum 16 B Drywall Gray 10% Cellulose 8 Gypsum Page 5 of 8

23 ASBESTOS BULK ANALYSIS By: POLARIZING LIGHT MICROSCOPY Client: Apex Environmental Management 7 Winchester Court Mauldin, SC Project: COA 710 Beechwood Ave ASBESTOS BULK PLM, EPA 600 METHOD Client ID Lab ID Lab Description Lab Attributes NON-ASBESTOS COMPONENTS Non- ASBESTOS % 17 B Drywall Gray 10% Cellulose 8 Gypsum 18 B Drywall Gray 10% Cellulose 8 Gypsum 19 B Drywall Gray 10% Cellulose 8 Gypsum 20 B Drywall Gray 10% Cellulose 8 Gypsum 21 B Window Glazing White 8 10% Calc Carb Paint 22 B Window Glazing White 8 10% Calc Carb Paint 23 B Sample Submitted for TEM Analysis 24 Layer 1 B Roof Shingle Off-white,Black 2 Fiberglass 40% 3 Tar Page 6 of 8

24 ASBESTOS BULK ANALYSIS By: POLARIZING LIGHT MICROSCOPY Client: Apex Environmental Management 7 Winchester Court Mauldin, SC Project: COA 710 Beechwood Ave ASBESTOS BULK PLM, EPA 600 METHOD Client ID Lab ID Lab Description Lab Attributes NON-ASBESTOS COMPONENTS Non- ASBESTOS % Layer 2 B Roof Shingle Black 80% Cellulose 20% Tar Layer 3 B Felt Paper Black 2 Fiberglass 40% 3 Tar 25 Layer 1 B Roof Shingle Off-white,Black 2 Fiberglass 40% 3 Tar Layer 2 B Roof Shingle Black 80% Cellulose 20% Tar Layer 3 B Felt Paper Black 2 Fiberglass 40% 3 Tar 26 B Sample Submitted for TEM Analysis Page 7 of 8

25 LEGEND: Non-Anth = Non-Asbestiform Anthophyllite Non-Trem = Non-Asbestiform Tremolite Calc Carb = Calcium Carbonate METHOD: EPA 600 / R93 / 116 and EPA 600 / M4-82 / 020 LIMIT OF DETECTION: <1% by visual estimation REGULATORY LIMIT: >1% by weight Due to the limitations of the EPA 600 method, nonfriable organically bound materials (NOBs) such as vinyl floor tiles can be difficult to analyze via polarized light microscopy (PLM). EPA recommends that all NOBs analyzed by PLM, and found not to contain asbestos, be further analyzed by Transmission Electron Microscopy (TEM). Please note that PLM analysis of dust and soil samples for asbestos is not covered under NVLAP accreditation. This report relates only to the samples tested or analyzed and may not be reproduced, except in full, without written approval by CEI Labs, Inc. CEI Labs makes no warranty representation regarding the accuracy of client submitted information in preparing and presenting analytical results. Interpretation of the analytical results is the sole responsibility of the client. This report may not be used by the client to claim product endorsement by NVLAP or any other agency of the U.S. Government. ANALYST: Taylor B. Metcalf APPROVED BY: Tianbao Bai, Ph.D., CIH Laboratory Director Page 8 of 8

26 February 24, 2016 Apex Environmental Management 7 Winchester Court Mauldin, SC CLIENT PROJECT: COA 710 Beechwood Ave CEI LAB CODE: T Dear Customer: Enclosed are asbestos analysis results for TEM bulk samples received at our laboratory on February 22, The samples were analyzed for asbestos using transmission electron microscopy (TEM) per Chatfield Method. Sample results containing > 1% asbestos are considered asbestos-containing materials (ACMs) per the EPA regulatory requirements. The detection limit for the TEM Chatfield method is <1% depending on the processed weight and constituents of the sample. Thank you for your business and we look forward to continuing good relations. If you have any questions, please feel free to call our office at Kind Regards, Tianbao Bai, Ph.D., CIH Laboratory Director 107 New Edition Court Cary, NC

27 ASBESTOS ANALYTICAL REPORT By: Transmission Electron Microscopy Prepared for Apex Environmental Management CLIENT PROJECT: COA 710 Beechwood Ave CEI LAB CODE: T TEST METHOD: Bulk Chatfield EPA 600 / R93 / 116 REPORT DATE: 02/24/16 TEL:

28 ASBESTOS BULK ANALYSIS By: TRANSMISSION ELECTRON MICROSCOPY Client: Apex Environmental Management 7 Winchester Court Mauldin, SC Project: COA 710 Beechwood Ave TEM BULK CHATFIELD / EPA 600 / R93 / 116 Client ID Lab ID Material Description Sample Weight (g) Organic Material % Acid Soluble Material % Acid Insoluble Material % Asbestos % 3 Tan, Patterned Floor Tile None T47152 Detected 3 Beige Gray Sheet Vinyl None T47153 Detected 3 Clear Mastic None T47154 Detected 6 Tan Gray Sheet Vinyl None T47155 Detected 6 Beige Gray Sheet Vinyl None T47156 Detected 6 Off-white Sheet Vinyl None T47157 Detected 23 White Window Glazing None T47158 Detected 26 Off-white Black Roof T47159 Shingle None Detected 26 Black Roof Shingle None T47160 Detected 26 Black Felt Paper None T47161 Detected Page 1 of 2

29 LEGEND: None METHOD: CHATFIELD & EPA/600/R-93/116 LIMIT OF DETECTION: Varies with the weight and constituents of the sample (<1%) REGULATORY LIMIT: >1% by weight This report relates only to the samples tested or analyzed and may not be reproduced, except in full, without written approval by CEI Labs, Inc. CEI Labs makes no warranty representation regarding the accuracy of client submitted information in preparing and presenting analytical results. Interpretation of the analytical results is the sole responsibility of the client. ANALYST: Kamila Reichert APPROVED BY: Tianbao Bai, Ph.D., CIH Laboratory Director Page 2 of 2

30

31

32 SECTION IV Photographic Log

33 Apex Asbestos Assessment 710 Beechwood Anderson, South Carolina 710 A&B Beechwood Avenue in Anderson, South Carolina Vinyl Flooring Vinyl floor tile

34 Apex Asbestos Assessment 710 Beechwood Anderson, South Carolina Wood Floor

35 SECTION V SC DHEC Asbestos Inspector License

36