The following additional instructions shall apply to and govern the Contract Documents.

Transcription

1 March 18, 2014 Addendum #1 E.C. St-Michel Building Envelope Upgrade New Liskeard, Ontario Project # The following additional instructions shall apply to and govern the Contract Documents. Item #1 Reference: Specifications Document Appendix C : Alternative Prices Additional Information Replace existing document with revised attached document. (1 page) Item #2 Reference: Specifications Additional Information Add the attached Document Appendix D: Add-In / Take-out Prices to the specifications. Provide Add-In price as noted. This information must be submitted with the Tender Form at the time of Bid Closing. Item #3 Reference: Specifications Document Designated Substance Report Additional Information Replace the existing report with the attached updated report. (39 pages) Vancouver Toronto Ottawa Timmins Thunder Bay Cornwall Sudbury PBK Architects Inc. 172 Algonquin Blvd. East, Timmins, ON, Canada, P4N 1A9 Telephone: (705) ~ Fax: (705) ~

2 Item #4 Reference: Specifications Details D9, D14, D19 Additional Information Contractor to refer to details D9, D14, D19 and allow for mineral fibre wool insulation to fill the cavity of the new parapet wall construction. Item #5 Reference: Specifications Detail D14 Additional Information Contractor to refer to detail D14 and add note Fill existing deck flutes with mineral fibre batt insulation as shown. Item #6 Reference: Specifications Document Construction Assembly Schedule Wall Types Clarification Walls Types W1 and W3 to be revised as follows: W1: 19x64mm prefinished fiber cement vertical batten board as 400mm O.C. (at steel studs) Prefinished fiber cement board as specified 25mm Vertical Z Girt as 400mm O.C. 100mm fiberglass 400mm horizontally (at steel studs) and 400mm O.C. vertically 115mm sprayed polyurethane foam insulation (RSi: 5.15) 13mm denglass gold sheathing 152mm wind load bearing steel 400mm O.C. 16mm type x gypsum board W3: Prefinished Lap siding as specified 25mm Vertical Z Girt as 400mm O.C. 100mm fiberglass 400mm horizontally and 600mm O.C. vertically on 184mm x thickness to suit continuous horizontal wood blocking 115mm sprayed polyurethane foam insulation (RSi: 5.15) Vancouver Toronto Ottawa Timmins Thunder Bay Cornwall Sudbury PBK Architects Inc. 172 Algonquin Blvd. East, Timmins, ON, Canada, P4N 1A9 Telephone: (705) ~ Fax: (705) ~

3 13mm denglass gold sheathing 152mm wind load bearing steel 400mm O.C. 16mm type X gypsum board Item #7 Reference: Specifications Section Spray-in-Place Urethane Insulation Clarification Replace the existing specification section with the revised section attached. (5 pages) Item #8 Reference: Specifications Section PVC Roofing 2.6 Walkway Protection Additional Information.1 Crossgrip Walkway In all instances, remove reference to roof Walkway protection (Crossgrip Walkway). This product is no longer required for the project. Item #9 Reference: Specifications Division 09 - Finishes Room Finish Schedule Clarification Replace existing document with revised Room Finish Schedule R1. (6 pages) Item #10 Reference: Drawings A1.1 Partial Demolition Floor Plans, Demolition Notes and Legend A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Clarification Refer to the attached revised Notes Legend ADD1.1 and ADD 1.2. Vancouver Toronto Ottawa Timmins Thunder Bay Cornwall Sudbury PBK Architects Inc. 172 Algonquin Blvd. East, Timmins, ON, Canada, P4N 1A9 Telephone: (705) ~ Fax: (705) ~

4 Item #11 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend General Notes Clarification Revise General Note #20 to read: Contractor to allow for 10 boxes of replacement ceiling tile to match existing within areas of renovation. Remaining tile upon completion of work is to be turned over to Owner for future use. Item #12 Reference: Drawings A1.1 Partial Demolition Floor Plans, Demolition Notes and Legend Drawing #5/A1.2 Partial Demolition Plan at Classrooms Clarification Revise note within Corridor #130 to read: Contractor to limit slab breakage to a minimum to allow for new washroom plumbing installations. Provide new VCT floor finish c/w rubber base as specified within Corridor #130. Extent of new VCT floor finish to be in line with west wall of Corridor #118. Provide good transition between new and existing Corridor VCT floor finishes. Item #13 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #5/A1.2 Partial Floor Plan at Classrooms Clarification Contractor to note there will be no children s cubbies within Classroom #132. Provide new whiteboard and tackboard arrangement to match south wall in Classroom #131. Vancouver Toronto Ottawa Timmins Thunder Bay Cornwall Sudbury PBK Architects Inc. 172 Algonquin Blvd. East, Timmins, ON, Canada, P4N 1A9 Telephone: (705) ~ Fax: (705) ~

5 Item #14 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #5/A1.2 Partial Floor Plan at Classrooms Clarification Remove specified porcelain floor tile finish within Classroom #132 and replace with VCT floor finish as specified. Item #15 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #5/A1.2 Partial Floor Plan at Classrooms Additional Information Contractor to provide 16 (sixteen) lockers, Type A as specified, in Corridor space along wall across from door #120. Item #16 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #5/A1.2 Partial Floor Plan at Classrooms Additional Information Remove new gypsum board chase within south-east corner of the room. Within classroom #108, Contractor to provide 64mm metal stud wall against existing west classroom wall. New stud partition wall to extend to underside of deck. Provide 16mm type x gypsum board finish c/w bullnose corners and gypsum board returns at existing door frame to remain. Contractor to extend/relocate services as required along this wall to suit new conditions. Item #17 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #5/A1.2 Partial Floor Plan at Classrooms Additional Information Within classroom #108, Contractor to allow for 92mm metal stud chase behind door #112 c/w metal access door based on 12 x12 UA Series by MIFAB. Contractor to provide additional 92mm metal Vancouver Toronto Ottawa Timmins Thunder Bay Cornwall Sudbury PBK Architects Inc. 172 Algonquin Blvd. East, Timmins, ON, Canada, P4N 1A9 Telephone: (705) ~ Fax: (705) ~

6 stud wall framing c/w 16mm type X wall for the extent of new cubbies to conceal existing radiator supply and return lines. Provide wood blocking and additional support as shown on drawings and as required. Exact location of wall to be coordinated on site with millwork construction requirements. Item #18 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #5/A1.2 Partial Floor Plan at Classrooms Clarification Within Classroom #111, note N37 to be revised to N33. Item #19 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #5/A1.2 Partial Floor Plan at Classrooms Clarification Within Classroom #128, note N33 to be revised to N34. Item #20 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #5/A1.2 Partial Floor Plan at Classrooms Clarification Within Classroom #110, note N2 along interior wall closet to be revised to N5. Item #21 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #4/A1.2 Partial Floor Plan at Second Floor Seminar Room Clarification Contractor to remove all lockers specified within room #208 Seminar Room. No work is to take place within this room. Vancouver Toronto Ottawa Timmins Thunder Bay Cornwall Sudbury PBK Architects Inc. 172 Algonquin Blvd. East, Timmins, ON, Canada, P4N 1A9 Telephone: (705) ~ Fax: (705) ~

7 Item #22 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #1/A1.2 Partial Floor Plan at Library #178 Clarification Disregard notes N14 and N42 within Library #178 Item #23 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #1/A1.2 Partial Floor Plan at Library #178 Clarification Contractor to note that all freestanding bookshelves will be cleared of books prior to construction by Owners forces. Existing bookshelves to be removed, salvaged and stored for reinstallation. Location for storage on site to be coordinated with Owner. Item #24 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend Drawing #5/A1.2 Partial Floor Plan at Classrooms Additional Information Contractor to repair existing door #112 to match existing. Provide wood filler and new paint finish at door and frame. Colour by Owner. Item #25 Reference: Drawings A1.2 Partial Floor Plans, Key Plan, Notes, General Notes and Legend General Notes Additional Information Contractor to remove existing wall-mounted raceway within areas of renovation aside from that next to existing doorway locations unless noted otherwise. Vancouver Toronto Ottawa Timmins Thunder Bay Cornwall Sudbury PBK Architects Inc. 172 Algonquin Blvd. East, Timmins, ON, Canada, P4N 1A9 Telephone: (705) ~ Fax: (705) ~

8 Item #26 Reference: Drawings A1.7 Partial Roof Plan, Notes and Legend Additional Information Contractor to allow for re-roofing of additional roof area noted on drawing ADD1.3. Allow for new 24ga. prefinished metal cap flashing at perimeter c/w scupper. Item #27 Reference: Drawings A1.7 Partial Roof Plan, Notes and Legend Drawing #1/A1.7 Partial Roof Plan Additional Information Contractor to remove roof vent box penetration at north portion of roof area #1. Associated ductwork into classroom #108, curbs and flashing to be removed. Provide metal pan roof decking welded to match existing c/w L3x3x1/4 framing around deck opening and extended to existing joists for support. Item #28 Reference: Drawings A1.7 Partial Roof Plan, Notes and Legend Drawing #/A1.7 Partial Roof Plan Additional Information Existing exhaust vents located on the vertical plane (east wall) at roof area #4 to be inspected for function. Contractor to include for the extension of service lines as required to suit reinstallation within new roof construction assembly. Item #29 Reference: Structural Drawings Additional Information Refer to attached Struc01 Addendum dated March 17, 2014 from WSP. (1 page) Vancouver Toronto Ottawa Timmins Thunder Bay Cornwall Sudbury PBK Architects Inc. 172 Algonquin Blvd. East, Timmins, ON, Canada, P4N 1A9 Telephone: (705) ~ Fax: (705) ~

9 Item #30 Reference: Mechanical Drawings Additional Information Refer to attached mechanical Addendum No. 1 dated March 10, 2014 from WSP. (5 pages) Item #31 Reference: Electrical Drawings Additional Information Refer to attached electrical Addendum No. 01 dated March 17, 2014 from WSP. (4 pages) End of Addendum Brett Weatherby, B.Sc. Arch., Dipl. Arch. Tech. PBK Architects Inc. Vancouver Toronto Ottawa Timmins Thunder Bay Cornwall Sudbury PBK Architects Inc. 172 Algonquin Blvd. East, Timmins, ON, Canada, P4N 1A9 Telephone: (705) ~ Fax: (705) ~

10 École catholique St-Michel Building Envelope Upgrade Addendum #1 - Document New Liskeard, Ontario APPENDIX C: ALTERNATIVE PRICES Project # Page 1 TENDER SUBMITTED BY: ALTERNATIVE PRICES The following are our prices for Alternative Work listed hereunder. Such Alternative Work and amounts are NOT included in our Base Bid. (If not used, bar and initial the space below.) Prices listed shall exclude the HST. Description of Alternate Work Effect on Base Bid ($) Addition Cost to substitute Sarnafil PVC membrane with Lexcan fully adhered PVC membrane. Deletion Contractor s Signature

11 École catholique St-Michel Building Envelope Upgrade Document New Liskeard, Ontario APPENDIX D: ADD-IN / TAKE-OUT PRICES Project # Page 1 TENDER SUBMITTED BY: ADD-IN PRICES The following are our Add-In prices for the work listed hereunder. Such Add-In Work and monetary amounts are NOT included in our Stipulated Price. (If not used, bar and initial the space below.) Prices listed shall exclude the H.S.T. Description of Add-In Work Effect on Stipulated Price ($) Addition Mechanical and electrical cost for Grinder Pumps in lieu of the specified sewage pumps. Refer to Mechanical Drawing M1.2 for Grinder pump specifications TAKE-OUT PRICES The following are our take out prices for Work listed hereunder. Such Work is included in our Stipulated Price. Should the Owner elect to delete this work, the base bid shall be reduced by the amounts shown below. (If not used, bar and initial the space below.) Prices listed shall exclude the H.S.T. Description of Take Out Work Effect on Stipulate Price ($) Deletion Contractor s Signature

12 DESIGNATED SUBSTANCE SURVEY ÉCOLE CATHOLIQUE ST MICHEL ROUTE 11 B NORD, NEW LISKEARD, ON APRIL 2009 Préparé par: 70C Mountjoy Street N Suite 125 Timmins, ON P4N 4V7

13 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel 1.0 INTRODUCTION Conseil Scolaire Catholique de Grandes Rivieres (CSCDGR) is a French Catholic School Board serving North Eastern Ontario. As part of due diligence as well as per regulatory requirements, BZ Environmental Consulting was retained by the CSCDGR, to complete a Designated Substance Inventory ( DSI ) for each of their Schools and buildings. The objective of the DSI was to identify and quantify designated substances as defined by the Ontario Occupational Health and Safety Act (OHSA) and the Ontario Ministry of Labour (MOL) including: asbestos-containing materials (ACM), lead, arsenic, benzene, mercury, vinyl chloride, acrylonitrile, silica, isocyanates coke oven emissions; ethylene oxides and other hazardous and designated substances including ozone-depleting substances, polychlorinated biphenyl (PCB)-containing equipment, urea formaldehyde foam insulation, and man-made mineral fibres. 1 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

14 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel 1.1 REGULATORY REQUIREMENTS This Designated Substance Report has been undertaken to fulfil the Conseil Scolaire Catholique de Grandes Rivieres (CSCDGR) requirements under Section 30 of the Ontario Occupational Health and Safety Act, (the OHSA ), Revised Statutes of Ontario 1990, (as amended). Conseil Scolaire Catholique de Grandes Rivieres (CSCDGR) must provide this report to all workers and contractors who may or may not come into contact with Designated Substances in the buildings. The Designated Substances defined under the OHSA and their corresponding regulations at the time of the survey are summarized in Table 1. Designated Substances as defined by the OHSA means a biological, chemical or physical agent or combination thereof prescribed as a designated substance to which the exposure of a worker is prohibited, regulated, restricted, limited or controlled. The OHSA has issued specific regulations under Section 30 of the Act for these substances. The Designated Substance Regulations identified under the Industrial Regulation of the OHSA, provide guidance on exposure and medical monitoring, permissible occupational exposure limits, etc. Ontario Regulation 278/05 ( O.Reg. 278/05 ) regulates the disturbance of asbestos on construction projects and is enforced by the Ontario Ministry of Labour ( MOL ). Ontario Regulation 111/04 ( O.Reg. 111/04 ) regulates the disturbance of silica on construction projects and is enforced by the Ontario Ministry of Labour ( MOL ). The appropriate reference document is entitled Guideline Silica on Construction Projects September Ontario Ministry of Labour. The MOL guideline for the control of lead exposures during the removal of lead on construction projects does not include criteria for categorizing lead-paint. The United States Department of Housing and Urban Development ( U.S. HUD ), and the Canadian Federal Hazardous Products Act ( HPA ), however, defines leadbased paint as any paint application containing at least 0.5% lead by weight (5,000 parts per million-ppm), if tested by chemical analysis. Paint samples found to contain concentrations of lead that exceeds 0.5% lead that exceeds 0.5% lead by weight are considered lead containing paint under the HPA. 2 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

15 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel 1.2 DESIGNATED SUBSTANCES Substance Acrylonitrile Arsenic Asbestos Designated Substanceasbestos on construction projects and in buildings and repair operations * Benzene Coke Oven Emissions Ethylene Oxide Isocyanates Lead Mercury Silica Vinyl Chloride Regulations R.R , Reg.835, as amended by O.Reg, 101/04 R.R , Reg.836, as amended by O.Reg, 102/04 R.R , Reg.837, as amended by O.Reg, 279/04 R.R , Reg.278/05 R.R , Reg.839, as amended by O.Reg, 105/04 R.R , Reg.840, as amended by O.Reg, 106/04 R.R , Reg.841, as amended by O.Reg, 107/04 R.R , Reg.842, as amended by O.Reg, 108/04 R.R , Reg.843, as amended by O.Reg, 109/04 R.R , Reg.844, as amended by O.Reg, 110/04 R.R , Reg.845, as amended by O.Reg, 111/04 R.R , Reg.846, as amended by O.Reg, 112/04 Note: * The disturbance of asbestos on construction projects is specifically regulated by Ontario Regulation 278/05. It classifies all disturbance of asbestos as Type 1, Type 2 or Type 3, each of which is associated with defined work practices. All asbestos material waste is subject to special handling and disposal practices, and must be removed prior to partial or full demolition. Disposal of asbestos waste is subject to General Waste Management Regulation O. Reg. 347 as amended by 461/05. 3 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

16 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel 2.0 DESIGNATED SUBSTANCE SURVEY Designated substances in the Province of Ontario are defined in accordance with the OHSA. The following section of this report provides an overview of the primary characteristics of such designated substances, their potential health effects and the potential presence of such substances at the School identified during the inspection. BZ Environmental representatives completed a School inspection and associated DSI on March 30 th, 2012 at Ecole Catholique St Michel, located at Route 11 B Nord, New Liskeard, ON. At the time of the DSI, BZ Environmental had access to all rooms within the school. 2.1 Acrylonitrile Acrylonitrile is a colourless to pale-yellow liquid at room temperature, with an unpleasant odour. It is used in the manufacturing of synthetic fibres, rubber, coatings and adhesives. Acrylonitrile is toxic by inhalation and by skin exposure. Low-level exposure to acrylonitrile may cause eye and skin irritation, headaches, nausea and vomiting. High level or prolonged exposure may result in damage to the heart, liver, kidneys, and central nervous system and acrylonitrile a known carcinogen. Site Conditions: Based on the examination of the School, it is not expected that acrylonitrile is present. However, there is a potential for release of acrylonitrile if plastic wire coatings and other materials combust during a fire. 2.2 Arsenic Arsenic is a silver/grey, brittle, crystalline solid at room temperature. Arsenic compounds are used as wood preservatives, insecticides, herbicides, and in metal alloys and are naturally present in certain minerals and soils. Arsenic is a poison and at high levels may cause death, cancer, nerve damage, stomach damage, intestinal damage, and skin damage. At lower levels it may cause nausea, diarrhoea, decreased production of red and white blood cells, and abnormal heart rhythm. Site Conditions: Based on the School inspection, no materials that may potentially contain arsenic were identified with the exception of any pressure treated wood exterior products, which typically contain chromated 4 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

17 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel copper arsenate (CCA) from the pressure treatment process of wood. As pressure treated wood products may be present but not visible, ie: hidden due to building finishes, caution should be taken during any demolition activities which may expose pressure treated wood. 2.3 Asbestos Asbestos is the name used for a group of fibrous minerals that occur naturally in soil and rock. Asbestos fibres were formerly used for primarily its insulating and fireproofing properties in roofing shingles, ceiling tiles, floor tiles, asbestos cement products, gaskets, insulation, paper products, and other Building and insulating products. Asbestos mainly affects the respiratory system. Inhalation of asbestos may result in the build-up of scar-like tissue resulting in cancer of the lungs and the surrounding membrane. Site Conditions: An asbestos survey was conducted as part of the DSI. The results of the asbestos survey are presented in Appendix A. A summary of Asbestos-Containing Materials Sampled during the DSI is presented in Table 1. A summary of Confirmed Asbestos-Containing Materials is presented in Table Asbestos Containing Materials There are over 3,000 asbestos containing materials ( ACM ), which can be divided into two broad categories: friable and non-friable. Friable ACMs are defined as materials that can be crumbled, pulverized and reduced to powder when dry using hand pressure. Typical friable materials include acoustical or decorative spray applications, fireproofing and thermal insulation. Non-friable ACMs are hard or manufactured products such as floor tiles, fire blankets, pre-formed manufactured cementitious insulation and wallboards, pipes, and siding, wherein the asbestos fibres are bound. 2.5 Benzene Benzene is a colourless liquid at room temperature, with a sweet odour. Benzene and benzene-containing compounds are components of crude oil and refined petroleum products such as gasoline and are present in coal, natural gas and other materials. Benzene is used to manufacture other chemicals, which are 5 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

18 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel used to make plastic, resin, nylon, rubber, lubricants, detergents, drugs, and other materials. Benzene is a human carcinogen. Exposures to benzene may cause dizziness, drowsiness, and unconsciousness. Long-term exposures may result in anaemia, leukemia, and damage to bone marrow. Site Conditions: Based on the School Inspection, BZ Environmental Consulting did not observe or identify and potential of benzene containing compounds. 2.6 Coke Oven Emissions Coke oven emissions are the airborne constituents of the by-products created by destructive distillation of coal and petroleum. Coke oven emissions are typically associated with the production of steel and coal processing/coke manufacture. Exposure to coke oven emissions is a potential cause of lung cancer. Dermal contact with coke oven emissions should be avoided. Site Conditions: Based on the School inspection, BZ Environmental Consulting did not observe or identify any potential for coke oven emissions to be present. 2.7 Ethylene Oxide Ethylene oxide is a colourless gas at room temperature and a liquid at 12 degrees Celsius. It is used in the manufacture of ethylene glycol, surfactants, fumigants, fungicides, and petroleum demulsifiers. Exposure routes include inhalation, ingestion, skin and/or eye contact. Exposure may cause irritation of the eyes, skin, nose and throat, headaches, nausea, and drowsiness. Exposure to high concentrations may cause frostbite, reproductive effects, convulsions, liver and kidney damage, and ethylene oxide is a known human carcinogen. Site Conditions: Based on the School inspection, no ethylene oxide containing substances were identified. 2.8 Lead Lead is a naturally occurring bluish-grey metal that is solid at room temperature. Lead is used in the manufacture of batteries, ammunition, solder, paint, and piping. 6 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

19 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel The routes of exposure to lead are limited to inhalation and ingestion of lead, with the highest risk of lead exposure being the inhalation of lead containing dust. Lead can damage the nervous system, kidneys, and the immune system. Site Conditions: A lead-based paint-sampling program was conducted as part of the DSI and is presented in further detail within Section 4.0. There is also the possibility of lead piping used throughout the School; however, none was visually identified during DSI. 2.9 Mercury Mercury is a naturally occurring metal. At room temperature it is a shiny, silvercoloured odourless liquid. When heated it becomes a colourless, odourless gas. Mercury is used in electrical switches, thermostats, thermometers, dental fillings, certain batteries, and some manufacturing processes. The nervous system is very sensitive to all forms of mercury; however, vapour is especially harmful as it directly reaches the brain. Exposure to high levels of mercury may permanently damage the brain, kidneys and a developing fetus. Short-term exposure may cause lung damage, nausea, vomiting, skin rashes, and eye irritation. Site Conditions: At the time of the School inspection, there were no electrical switches, thermostats, thermometers, or any other electrical equipment that may contain mercury observed as being present in the School Silica Silica is a transparent to gray odourless powder or crystal at room temperature. It occurs widely in nature as sand, quartz, flint, and diatomite. Silica is used in the manufacture of glass, ceramics, abrasives, water treatment products, cosmetics, insecticides, paint and foods, as well as a drying agent or preservative. Crystalline silica materials also are used in the production of concrete, cement, acoustic ceiling tiles, and ceramic tiles which are used for construction purposes. The Ministry s designated substance regulation for silica, Regulation 845, specifies occupational exposure limits (OELs) for silica and requires assessment and a control program to ensure compliance with these OELs. The OEL for respirable crystalline silica is 0.05 milligrams per cubic metre (mg/m3) of air by volume as an 8-hour daily or 40-hour weekly time-weighted average for 7 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

20 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel cristobalite and tridymite. In the case of quartz and Tripoli, the OEL is 0.10 milligrams per cubic meter of air by volume. Site Conditions: Based on the School inspection, crystalline silica is likely present in the building concrete (e.g., concrete slab floor and concrete block walls). As such, there is a potential for silica dust to be generated by the grinding, cutting, renovating, or demolition of School s materials Vinyl Chloride Vinyl chloride is a colourless, flammable gas at room temperature with a mild, sweet odour; Vinyl chloride is a degradation product of product of organic industrial/commercial solvents such as tetrachloroethylene (PCE) and trichloroethylene (TCE), which are used as degreasing and dry cleaning agents. One use of vinyl chloride is in the manufacture of polyvinyl chloride (PVC), which is used in many plastic products including plastic pipe, electrical cable insulation, plumbing and conduit fixtures, clothing, upholstery, roofing and flooring materials. Exposure to vinyl chloride occurs mainly in workplaces where it is used in plastic product manufacturing or chlorinated solvents are used. Breathing high levels of vinyl chloride for short periods of time can cause dizziness, sleepiness, unconsciousness, and, damage, immune reactions, nerve damage, and cancer. Site Conditions: Based on the examination of the School, it is not expected that vinyl chloride is present. However, there is the potential for release of vinyl chloride if building piping and wire cable coatings combust during a fire. 8 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

21 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel 3.0 ASBESTOS SURVEY 3.1 General The asbestos containing material (ACM) survey was conducted on April 22, A second visit to the school was done on June 23 rd 2011, and a third visit to the school was completed on March 30 th, The asbestos survey was completed with consideration to Ontario Regulation (O.Reg.) 278/05 entitled Designated Substance Asbestos on Construction Projects and in Buildings and Repair Operations. O.Reg. 278/05 revoked and replaced O.Reg. 838/90 on November 1, Sampling activities were performed in accordance with bulk asbestos sampling procedures outlined in O.Reg 278/05 and in the document entitled Designated Substances in the Workplace: A Guide to the Asbestos Regulation for Construction Projects, Buildings and Repair Operations, MOL, April In areas where finished surfaces required partial removal to inspect hidden materials (e.g., surface coverings on pipe insulation and multiple layers of flooring material), openings were made by BZ Environmental to allow for inspection of the underlying materials. 3.2 Sampling Representatives of BZ Environmental Consulting performed a Site inspection and associated DSI on April 22, 2009, whereby all accessible areas of the school were examined. A second visit to the school was done on June 23 rd 2011, and a third visit to the school was completed on March 30 th, The inspection consisted of a visual survey of accessible interior and exterior areas and included the collection of select representative building material samples. Based on the age and use of the building, the assessment focused on identifying the most common applications of building materials likely to contain Designated Substances. Representative bulk samples of building materials suspected of containing asbestos were collected for analysis. Eleven (11) suspected asbestos-containing materials were submitted in triplicate to EMSL Analytical, Inc, in Westmount, NJ. EMSL Analytical is accredited for bulk asbestos fibre analysis. Samples were analyzed using polarized light microscopy ( PLM ) technique (following method EPA/600/R-93/116). This standard is specified by Ontario Regulation 278/05 as the method for establishing whether the material is asbestos-containing and defining the content 9 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

22 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel and type of asbestos. Triplicate samples taken in order to satisfy the requirements of Ontario Regulation 278/ BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

23 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel All samples identified to have an asbestos content of 0.5% or higher are summarized in Table 2. The survey included minimal destructive testing of drywall surfaces. However, it is possible that materials may exist which could not be reasonably identified within the scope of the assessment or which were not apparent or accessible during the site visit. An area above a suspended tile ceiling, behind a closed door, or behind an access hatch is considered accessible. An area enclosed by gypsum board, plaster, or panelling, roofing materials, boiler refractory, etc., where minor demolition is required to gain entry, is considered non-accessible and was not included as part of this investigation TABLE 1 SAMPLES SUBMITTED WITH ASBESTOS CONTENT 2009 Sample ID Material Description Location Condition 1 a-b-c 9 X 9 Floor Tile (green) hallway Good 2 a-b-c Elbow Pipe Cement hallway Good 3 a-b-c Elbow Pipe Cement Hallway - black Good 4 a-b-c Ceiling Tile Classroom Good SAMPLES SUBMITTED WITH ASBESTOS CONTENT 2011 Sample ID Material Description Location Condition 1 a-b-c Floor Tile green Music Room (135) Good 2 a-b-c Floor Tile beige Room 160 Good 3 a-b-c Floor Tile beige Room 122 Good 4 a-b-c Floor Tile white Room 108 Good 5 a-b-c Floor Tile white Room 119 Good 6 a-b-c Floor Tile white Room 110 Good 7 a-b-c Floor Tile - green Hallway Good 11 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

24 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel Definitions of Condition Good Condition: - Non-Friable - Asbestos is well maintained and is very unlikely to become friable - Friable asbestos is fully encapsulated and is not airborne Fair Condition: - Non-Friable asbestos is maintained but may need future attention if left alone. - Friable asbestos is encapsulated but may need further attention if left alone. Poor Condition: - Non-Friable asbestos is cracking and breaking and may become friable. - Friable asbestos may be airborne. - Enclosure and removal is highly recommended TABLE 2 CONFIRMED ASBESTOS CONTAINING MATERIAL RECORD 2009 Sample Material Description Friable or Asbestos % & Type ID Non-Friable 1a-b-c 9 X 9 Floor Tile (green) Non-Friable 2% Chrysotile 2 a-b-c Elbow Pipe Cement Hallway Non-Friable None Detected 3 a-b-c Elbow Pipe Cement Black Non-Friable None Detected 4 a-b-c Ceiling Tile Non-Friable None Detected CONFIRMED ASBESTOS CONTAINING MATERIAL RECORD 2011 Sample Material Description Friable or Asbestos % & Type ID Non-Friable 1 a-b-c Floor Tile green Non-Friable 4% Chrysotile 2 a-b-c Floor Tile beige Non-Friable 2% Chrysotile 3 a-b-c Floor Tile beige Non-Friable None Detected 4 a-b-c Floor Tile white Non-Friable 8% Chrysotile 5 a-b-c Floor Tile white Non-Friable 5% Chrysotile 6 a-b-c Floor Tile white Non-Friable 9% Chrysotile 7 a-b-c Floor Tile - green Non-Friable 4% Chrysotile 12 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

25 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel 3.3 Confirmed ACM Based on the analytical report, seven of the building materials collected contained asbestos fibres in exceedance of 0.5 percent. 13 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

26 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel 4.0 LEAD PAINT SURVEY 4.1 General A lead paint-sampling inspection was conducted during the April 22, 2009, School inspection. Sampling activities were performed in accordance with bulk lead sampling procedures outlined in the document entitled Designated Substances in the Workplace: A Guide to the Lead Regulation for Construction Projects, Buildings and Repair Operations, MOL, Ontario Regulation 843 (1990). The above-mentioned sampling protocol is recommended by the MOL for lead paint sampling. As part of this lead paint survey, there was one paint chip sample collected. Sample ID Material Description Location Condition 5 a-b-c Paint Hallway Good 4.2 Analytical Results One Paint chip sample was collected during the inspection. The results of this sample indicated lead levels ranging from 0.020% % by weight and should be considered lead free. No guidelines exist in the Province of Ontario defining when a coating is considered to be lead-based. However, Ontario Regulation 109/04 stipulates that workers are not to be exposed to airborne lead levels in exceedance of the TWAEV or MAC values outlined in the regulation. BZ Environmental Consulting recommends that the measures outlined in the Ministry of Labour s Guideline for Lead on Construction Project (September 2004) be put into place to control potential lead dust hazard during any work, which involves the disturbance of a painted surface. This is particularly important for painted surfaces that exhibit elevated concentrations of lead identified during the DSI. Sample Material Description Lead Concentration Condition ID 5 a-b-c Paint None Detected Good 14 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

27 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel 5.0 CONCLUSIONS A designated substance survey was completed at Ecole Catholique St Michel located at Route 11 B North in New Liskeard, ON, on April 22, A second visit to the school was done on June 23 rd 2011, and a third visit to the school was completed on March 30 th, A total of eleven (11) samples were identified as suspected Asbestos Containing Material and one (1) sample was identified as suspected lead containing material. Laboratory analysis determined that seven (7) of these samples were Asbestos containing and the lead suspected material did not exceeds the limits. Silica was suspected to be present in sand, concrete, brick and mortar. There were no immediate dangers found with any of these substances. There were no other issues identified. Representative samples Please assume that all similar materials found within buildings will have similar asbestos and/or lead content when materials are found from the same construction year in the same building. 6.0 LIMITATIONS The information, conclusions and recommendations given herein are specifically for this project and this client only, and the scope of work described herein. It may not be sufficient for other uses. The conclusions and recommendations regarding environmental conditions, which are presented in this report are based on a scope of work authorized by the Client, however, it should be noted that virtually no scope of work, no matter how exhaustive, can identify all contaminants or all conditions above and below ground. For example, conditions between test holes or sample locations may differ from those encountered in the investigation and conditions may change with time. This report therefore cannot warranty that all conditions on or off the site are represented by those identified at specific locations. The services performed as described in this report were based on visual observations of the site, structures and outbuildings. There were no destructive investigations performed at this site. Note also that standards, guidelines and practices related to environmental investigations may change with time. Those that were applied at the time of this investigation may be obsolete or unacceptable at a later date. 15 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

28 March 30 th, 2012 Designated Substance Survey CSCDGR Ecole Catholique St. Michel The comments given in this report on potential remediation problems and possible methods are intended only for the guidance of the designer. The scope of work may not be sufficient to determine all of the factors that may affect construction or clean-up methods and costs. Any results from an analytical laboratory reported herein have been carried out by others, in this case, EMSL Analytical and BZ Environmental Consulting does not warranty their accuracy. All laboratories used by BZ Environmental Consulting are accredited by the appropriate authorities for the specific registered tests. 7.0 CLOSURE We trust this information is sufficient for your present purposes. Should you have any questions, please do not hesitate to contact the undersigned directly. Yours Truly, BZ ENVIRONMENTAL Mark J. Bednarz, B.E.S., P.Geo., Sr. Environmental Geoscientist Stephane Mousseau Environmental Technician 16 BZ Environmental Consulting 70C Mountjoy Street N., Suite 125, Timmins, ON P4N 4V7

29

30

31 EMSL Analytical, Inc. 107 Haddon Ave., Westmont, NJ Phone: (856) Fax: (856) Attn: Mark Bednarz BZ Environmental Consulting 70 C Mount Joy Street North Suite 125 Timmins, ON P4N 4V7 Fax: (705) Phone: (705) Project: Customer ID: Customer PO: Received: EMSL Order: EMSL Proj: Analysis Date: BZEN78 04/28/09 9:20 AM /30/2009 Asbestos Analysis of Bulk Materials for Ontario Regulation 278/05 via EPA600/R-93/116 Method Client Sample ID: Sample Description: Test 1A TILE GREEN HALLWAY FLOOR TILE Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Olive 0% 98% 2% Chrysotile Client Sample ID: Sample Description: Test 1A MASTIC GREEN HALLWAY FLOOR TILE Lab Sample ID: A Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Black 0% 100% None Detected Client Sample ID: Sample Description: Test 1B TILE GREEN HALLWAY FLOOR TILE Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Olive 0% 98% 2% Chrysotile Client Sample ID: Sample Description: Test 1B MASTIC GREEN HALLWAY FLOOR TILE Lab Sample ID: A Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Black 0% 100% <1% Chrysotile Client Sample ID: Sample Description: Test 1C TILE GREEN HALLWAY FLOOR TILE Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Olive 0% 98% 2% Chrysotile Client Sample ID: Sample Description: Test 1C MASTIC GREEN HALLWAY FLOOR TILE Lab Sample ID: A Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Black 0% 100% None Detected OntarioEPA Printed: 4/30/ :42:41 PM Page 1

32 EMSL Analytical, Inc. 107 Haddon Ave., Westmont, NJ Phone: (856) Fax: (856) Attn:Mark Bednarz BZ Environmental Consulting EMSL Proj: Asbestos Analysis of Bulk Materials for Ontario Regulation 278/05 via EPA600/R-93/116 Method Client Sample ID: Sample Description: Test 2A PIPE WRAP "INSULATION" HALLWAY Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Brown 90% 10% None Detected Client Sample ID: Sample Description: Test 2B PIPE WRAP "INSULATION" HALLWAY Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Brown 90% 10% None Detected Client Sample ID: Sample Description: Test 2C PIPE WRAP "INSULATION" HALLWAY Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Brown 90% 10% None Detected Client Sample ID: Sample Description: Test 3A PIPE WRAP - HALLWAY. BLACK. Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Black 60% 40% None Detected Client Sample ID: Sample Description: Test 3B PIPE WRAP - HALLWAY. BLACK. Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Black 60% 40% None Detected Client Sample ID: Sample Description: Test 3C PIPE WRAP - HALLWAY. BLACK. Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Black 60% 40% None Detected Client Sample ID: Sample Description: Test 4A CEILING TILE Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Brown/White 85% 15% None Detected Client Sample ID: Sample Description: Test 4B CEILING TILE Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Brown/White 75% 25% None Detected OntarioEPA Printed: 4/30/ :42:42 PM Page 2

33 EMSL Analytical, Inc. 107 Haddon Ave., Westmont, NJ Phone: (856) Fax: (856) Attn:Mark Bednarz BZ Environmental Consulting EMSL Proj: Asbestos Analysis of Bulk Materials for Ontario Regulation 278/05 via EPA600/R-93/116 Method Client Sample ID: Sample Description: Test 4C CEILING TILE Lab Sample ID: Analyzed Non Asbestos Date Color Fibrous Non-Fibrous Asbestos Comment PLM 4/30/2009 Brown/White 85% 15% None Detected PLM: Analyst(s) Erica Valent Nancy Stalter Stephen Siegel, CIH, Laboratory Manager or other approved signatory None Detected = <0.5%. EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported above and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. Samples received in good condition unless otherwise noted. This report must not be used to claim product endorsement by NVLAP of any agency of the U.S. Government. AIHA IHLAP , NVLAP Lab Code , NYS ELAP OntarioEPA Printed: 4/30/ :42:43 PM THIS IS THE LAST PAGE OF THE REPORT. Page 3

34

35

36 EMSL Analytical, Inc. 3 Cooper St., Westmont, NJ Phone: (856) Fax: (856) westmontleadlab@emsl.com Attn: Mark Bednarz BZ Environmental Consulting 70 C Mount Joy Street North Suite 125 Timmins, ON P4N 4V7 Fax: (705) Phone: (705) Project: Customer ID: BZEN78 Customer PO: CC Received: 04/28/09 12:00 PM EMSL Order: EMSL Proj: Lead in Paint Chips by Flame AAS (SW B*/7420) Client Sample Description Lab ID Collected Analyzed 5A /30/2009 Hallway 5B /30/2009 Hallway 5C /30/2009 Hallway Lead Concentration <0.020 % wt <0.032 % wt <0.028 % wt Shannon Kauffman, Lead Lab Supervisor or other approved signatory Reporting limit is 0.01 % wt. The QC data associated with these sample results included in this report meet the method quality control requirements, unless specifically indicated otherwise. Unless noted, results in this report are not blank corrected. This report relates only to the samples reported above and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities. * slight modifications to methods applied Samples received in good condition unless otherwise noted. Quality Control Data associated with this sample set is within acceptable limits, unless otherwise noted ACCREDITATIONS: NJ-NELAP: 04653, AIHA Environmental Lead Laboratory Approval Program: ChmSnglePrm/nQC Printed: 5/1/ :24:18 A Page 1 of 1

37

38

39 Asbestos Lead Environmental Materials & Indoor Air Analysis EMSL Canada Inc. 10 Falconer Drive, Unit #3 Mississauga, ON L5N 3L8 Phone: Fax: (289) Web: Attn: Mark Bednarz BZ Environmental Consulting 70 C Mount Joy Street North Suite 125 Timmins, ON P4N 4V7 Fax: (705) Phone: (705) Proj: /ST. MICHAEL EMSL Order: Customer ID: 55BZEN78 Collected: Received: 7/13/2011 Test Report: Asbestos Analysis of Bulk Materials for Ontario Regulation 278/05 via EPA600/R-93/116 Method Client Sample ID: Sample Description: 1A VERT (REFECTOIRE) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 White/Green 0% 96% 4% Chrysotile Client Sample ID: Sample Description: 1B VERT (REFECTOIRE) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 White/Green 0% 96% 4% Chrysotile Client Sample ID: Sample Description: 1C VERT (REFECTOIRE) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 White/Green 0% 95% 5% Chrysotile Client Sample ID: Sample Description: 2A 12x12 BEIGE (160) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Tan 0% 98% 2% Chrysotile Client Sample ID: Sample Description: 2B 12x12 BEIGE (160) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Tan 0% 99% 1% Chrysotile Client Sample ID: Sample Description: 2C 12x12 BEIGE (160) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Tan 0% 97% 3% Chrysotile Client Sample ID: Sample Description: 3A 12x12 BEIGE (122) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Tan/White 0% 100% None Detected Test Report:EPAMultiTests Printed: 7/27/ :22PM Page 1 of 3

40 EMSL Canada Inc. 10 Falconer Drive, Unit #3 Mississauga, ON L5N 3L8 Phone: Fax: (289) Web: Attn: Mark Bednarz BZ Environmental Consulting 70 C Mount Joy Street North Suite 125 Timmins, ON P4N 4V7 Proj: /ST. MICHAEL Test Report: Asbestos Analysis of Bulk Materials for Ontario Regulation 278/05 via EPA600/R-93/116 Method Client Sample ID: Sample Description: 3B 12x12 BEIGE (122) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Tan/White 0% 100% None Detected Client Sample ID: Sample Description: 3C 12x12 BEIGE (122) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Tan/White 0% 100% None Detected Client Sample ID: Sample Description: 4A BLANC (108) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Tan 0% 92% 8% Chrysotile Client Sample ID: Sample Description: 4B BLANC (108) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Tan/Various 0% 92% 8% Chrysotile Client Sample ID: Sample Description: 4C BLANC (108) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Tan/Various 0% 92% 8% Chrysotile Client Sample ID: Sample Description: 5A BLANC (119) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Gray/Black 0% 95% 5% Chrysotile Client Sample ID: Sample Description: 5B BLANC (119) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Gray/Black 0% 95% 5% Chrysotile Client Sample ID: Sample Description: 5C BLANC (119) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Gray/Black 0% 95% 5% Chrysotile Test Report:EPAMultiTests Printed: 7/27/ :22PM Page 2 of 3

41 EMSL Canada Inc. 10 Falconer Drive, Unit #3 Mississauga, ON L5N 3L8 Phone: Fax: (289) Web: Attn: Mark Bednarz BZ Environmental Consulting 70 C Mount Joy Street North Suite 125 Timmins, ON P4N 4V7 Proj: /ST. MICHAEL Test Report: Asbestos Analysis of Bulk Materials for Ontario Regulation 278/05 via EPA600/R-93/116 Method Client Sample ID: Sample Description: 6A 9x9 BLANC (110) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Brown/Tan 0% 90% 10% Chrysotile Client Sample ID: Sample Description: 6B 9x9 BLANC (110) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Brown/Tan 0% 92% 8% Chrysotile Client Sample ID: Sample Description: 6C 9x9 BLANC (110) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 Brown/Tan 0% 90% 10% Chrysotile Client Sample ID: Sample Description: 7A 12x12 VERT (COULOIR) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 White/Green 0% 97% 3% Chrysotile Client Sample ID: Sample Description: 7B 12x12 VERT (COULOIR) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 White/Green 0% 95% 5% Chrysotile Client Sample ID: Sample Description: 7C 12x12 VERT (COULOIR) Lab Sample ID: Analyzed Non-Asbestos TEST Date Color Fibrous Non-Fibrous Asbestos Comment PLM 7/27/2011 White/Green 0% 96% 4% Chrysotile Initial report from: 07/27/201118:22:11 Analyst(s) Kevin Pang PLM (21) Kevin Pang or other Approved Signatory Any questions please contact Kevin Pang. None Detected = <0.5%. EMSL maintains liability limited to cost of analysis. This report relates only to the samples reported above and may not be reproduced, except in full, without written approval by EMSL. EMSL bears no responsibility for sample collection activities or analytical method limitations. Interpretation and use of test results are the responsibility of the client. Samples received in good condition unless otherwise noted. This report must not be used to claim product endorsement by NVLAP of any agency of the U.S. Government. Samples analyzed by EMSL Canada Inc. Mississauga, ON NVLAP Lab Code Test Report:EPAMultiTests Printed: 7/27/ :22PM Page 3 of 3

42 DESIGNATED SUBSTANCE SURVEY ECOLE CATHOLIQUE ST. MICHEL 77 River St. Englehart, ON Location/Area: Room 160 Photos # : Room Characteristics Non-Suspect Materials Other Non-Suspect Materials Floor Wall Ceiling 9 x 9 floor tiles Drywall Drop Ceiling Photo # 1 Photo # 2 Photo # 3 Photo # 4 Suspect Material Colour Sample No. Analytical Results % Type/PPM 9 x 9 Floor Tile Beige 2A2B2C 2 % Chrysotile 3 Photo # Friability Non- Friable Condition Rating Good Page 1

43 DESIGNATED SUBSTANCE SURVEY ECOLE CATHOLIQUE ST. MICHEL 77 River St. Englehart, ON Location/Area: Room 122 Photos # : Room Characteristics Non-Suspect Materials Other Non-Suspect Materials Floor Wall Ceiling 9 x 9 floor tiles Drywall Drop Ceiling Photo # 1 Photo # 2 % Type/PPM Photo # Friability Condition Rating 9 x 9 Floor Tile Beige 3A3B3C Asbestos not detected 2 Non- Friable Good Page 2

44 DESIGNATED SUBSTANCE SURVEY ECOLE CATHOLIQUE ST. MICHEL 77 River St. Englehart, ON Location/Area: Hallway Photos # : Room Characteristics Non-Suspect Materials Other Non-Suspect Materials Floor Wall Ceiling 9 x 9 Floor Tiles Drywall/cement blocks Drywall Photo # 1 Photo # 2 Photo # 3 Photo # 4 Photo # 5 Photo # 6 Analytical Results Photo Condition Suspect Material Colour Sample No. Friability % Type/PPM # Rating 9 x 9 Floor Tiles Green 7A7B7C 4% Chrysotile Non-friable Good 9 x 9 Floor Tiles Green 1A1B1C 2% Chrysotile Non-friable Good Asbestos not Elbow Pipe Cement White 2A2B2C 5 Friable Good detected Elbow Pipe Cement Black 3A3B3C Asbestos not detected 4 Friable Good 9 x 9 Floor Tile White 5% Chrysotile Non-friable Good Paint Chip 5A5B5C Lead not detected 6 Friable Good Page 3

45 DESIGNATED SUBSTANCE SURVEY ECOLE CATHOLIQUE ST. MICHEL 77 River St. Englehart, ON Location/Area: Refectoire - Room 135 Photos # : Room Characteristics Non-Suspect Materials Other Non-Suspect Materials Floor 9 x 9 floor tile Possible ACM Mercury Thermostate Wall Ceiling Drywall/ Drywall Photo # 1 Photo # 2 Photo # 3 Analytical Results Photo Condition Suspect Material Colour Sample No. Friability % Type/PPM # Rating 9 x 9 floor tile Green 1A1B1C 4% Chrysotile 3 Non-friable Good Page 4

46 DESIGNATED SUBSTANCE SURVEY ECOLE CATHOLIQUE ST. MICHEL 77 River St. Englehart, ON Location/Area: Room 119 Photos # : Room Characteristics Non-Suspect Materials Other Non-Suspect Materials Floor Wall Ceiling 9 x 9 Floor Tile Cement blocks with drywall over it Drop ceiling Photo # 1 Analytical Results Photo Condition Suspect Material Colour Sample No. Friability % Type/PPM # Rating 9 x 9 Floor Tile White 5A5B5C 5% Chrysotile 2 Non-friable Good Also found in Room 132 Page 5

47 DESIGNATED SUBSTANCE SURVEY ECOLE CATHOLIQUE ST. MICHEL 77 River St. Englehart, ON Location/Area: Room 108 Photos # : Room Characteristics Non-Suspect Materials Other Non-Suspect Materials Floor Wall Ceiling 9 x 9 Floor Tile Cement blocks with drywall over it Drop ceiling Photo # 1 Photo # 2 Analytical Results Photo Condition Suspect Material Colour Sample No. Friability % Type/PPM # Rating 9 x 9 Floor Tile White 4A4B4C 8% Chrysotile 2 Non-friable Good Page 6

48 DESIGNATED SUBSTANCE SURVEY ECOLE CATHOLIQUE ST. MICHEL 77 River St. Englehart, ON Location/Area: Room 110 Photos # : Room Characteristics Non-Suspect Materials Other Non-Suspect Materials Floor Wall Ceiling 9 x 9 Floor Tile Cement blocks with drywall over it Drop ceiling Photo # 1 Photo # 2 Photo # 3 Analytical Results Photo Condition Suspect Material Colour Sample No. Friability % Type/PPM # Rating 9 x 9 Floor Tile White 6A6B6C 9% Chrysotile 2 Non-friable Good Ceiling Tile White 4A4B4C Asbestos not detected 3 Non-friable Good Page 7

49

50

51 École catholique St-Michel Building Envelope Upgrade Section New Liskeard, Ontario SPRAYED IN PLACE URETHANE INSULATION Project # Page 1 1 General 1.1 GENERAL REQUIREMENT.1 Conform to sections of Division 1 as applicable. 1.2 RELATED WORK.1 Section Wind-Load Bearing Steel Stud System.2 Section Rough Carpentry installation of fiberglass spacers, girts and blocking.3 Section Prefinished Fiber Cement Siding.4 Section Joint Sealers 1.3 REFERENCES.1 CAN/ULC S705.2 Spray Applied Rigid Polyurethane Cellular Plastic Thermal Insulation..2 Closed Cell Medium Density CAN/ULC S Closed Cell Medium Density CAN/ULC S Single component bead sealant CAN/ULC S Single component bead sealant CAN/ULC S Two component bead sealant CAN/ULC S Two component bead sealant CAN/ULC S National Energy Conservation Association (NECA)..9 Canadian Urethane Foam Contractors Association (CUFCA) Quality Assurance Program, June Quality Assurance Professionals (QAP) Quality Assurance Program. 1.4 SUBMITTALS.1 Submit six (6) copies of shop drawings to requirements of Section Submittals..2 Shop Drawings: Provide drawings of construction and expansion joint conditions and junctions between dissimilar materials..3 Product Data: Provide data on insulation material characteristics, performance criteria, limitations and compatibility..4 Submit test reports, verifying qualities of insulation meet or exceed requirements of this specification..5 Manufacturer s Installation Instructions: Indicate preparation, installation requirements and techniques, product storage and handling criteria, for insulation.

52 École catholique St-Michel Building Envelope Upgrade Section New Liskeard, Ontario SPRAYED IN PLACE URETHANE INSULATION Project # Page 2.6 Provide copy of Foam Contractor s Photo ID license card issued by CUFCA or QAP Quality Assurance Program. Installers must provide copies of their installer card that shows reference to their training provider and certification for the material being used..7 Copy of Applicator s Certification and documentation that the applicators have complete the CUFCA/NECA or QAP/EXOVA, Quality Assurance Program. 1.5 QUALITY ASSURANCE.1 Application of insulation/air seal system only by applicators certified by either CUFCA/NECA (Canadian Urethane Foam Contractors Association/National Energy Conservation Association) or Quality Assurance Professionals (QAP)/EXOVA Canada..2 Maintain one copy of installation manual on site..3 Installers of insulation/air seal system to perform daily on-site testing and maintain daily work reports in accordance with the Material Manufacturer s Quality Assurance Program and to the satisfaction of the Consultant. 1.6 PROTECTION.1 In enclosed areas of application, ventilate area to receive insulation by introducing fresh air and exhausting air continuously during and 24 hr. after application to maintain nontoxic, unpolluted, safe working conditions..2 Provide temporary enclosures to prevent spray and noxious vapours from contaminating air beyond interior application area..3 Protect workers as recommended by insulation manufacturer..4 Protect adjacent surfaces and equipment from damage by overspray, fall-out, and dusting of insulation materials..5 Legally dispose of waste foam daily and decontaminate empty drums in accordance with foam manufacturer s instructions..6 Clean spills immediately in accordance with manufacturer s written instructions and authorities having jurisdiction. 1.7 QUALIFICATIONS.1 Installer to be Qualified Applicator of the products from the manufacturer/distributor - Submit proof of status..2 Material manufacturer/distributor must have an on site quality assurance program. Submit duplicate copy of quality assurance program. 1.8 MOCK-UP.1 Provide mock-up of materials under provisions of Section Quality Control..2 Construct typical exterior wall panel, 3m long by 1m wide, incorporating window and door frames and sills, insulation, building corner condition and control and expansion joint conditions, illustrating materials interface and seals.

53 École catholique St-Michel Building Envelope Upgrade Section New Liskeard, Ontario SPRAYED IN PLACE URETHANE INSULATION Project # Page 3.3 Mock-up may remain as part of the Work if approved. 1.9 PRE-INSTALLATION CONFERENCE.1 Convene one week prior to commencing work of this section, under provisions of Section Project Coordination and Project Meetings. Meeting shall be attended by the Project Manager, Field Quality Assurance provider Inspector, Insulation Applicator and the Consultant ENVIRONMENTAL REQUIREMENTS.1 Maintain temperature and humidity recommended by the materials manufacturer before, during and after installation COORDINATION.1 Coordinate the work of this Section with all affected trades including:.1 Section Wind-Load Bearing Steel Stud System.2 Section Rough Carpentry.3 Section Prefinished Fiber Cement Siding.4 Section Joint Sealers 1.12 WARRANTY.1 Warrant work of this Section against defects or deficiencies for a period of two years from date Work is substantially performed in accordance with General Condition of the Contract..2 Promptly correct, at own expense, defects of deficiencies which become apparent within the warranty period TESTING.1 Employ the services of Field Quality Assurance provider certified inspector to perform onsite review and testing to confirm compliance with these specifications. Inspector shall inspect and report prior to application and inspect, test and report at 50% and 100% complete stages. 2 Products 2.1 MATERIALS.1 Foam Insulation: sprayed/rigid polyurethane foam to CAN/ULC S705.1, CAN/ULC S705.2 and CCMC 07272, flame spread rating of less than 500, aged RSI value of 1.05m² K/W per 25mm. thickness at a density of 32.2 to 32.8 kg/m³. Acceptable products include BASF WALLTITE Eco v.3, Premium Spray Products FOAMSULATE ECO or approved equal. Thickness to be applied as indicated on architectural drawings and partition schedule..2 Transition Membrane to be used at all control joints and between all joints dissimilar materials prior to the application of the insulation. Install in widths of 300mm with 150mm cover to each side, and as noted on details. Material: Blueskin SA self-adhesive membrane complete with Blueskin Primer as manufactured by Bakor.

54 École catholique St-Michel Building Envelope Upgrade Section New Liskeard, Ontario SPRAYED IN PLACE URETHANE INSULATION Project # Page COMPATIBILITY.1 Ensure that all materials used are compatible..2 Provide proof of compatibility upon request. 3 Erection 3.1 PRODUCT DELIVERY, STORAGE AND HANDLING.1 Deliver materials in original unopened containers..2 Label containers with brand name, installation instructions and identification of various items..3 Store materials except membrane between 15 C and 27 C. If exposed to lower temperature restore to acceptable level before using..4 Store materials except membrane in dry area and protect. 3.2 EXAMINATION.1 Verify that surfaces and conditions are ready to accept the work of this section. Application of work of this section shall be deemed acceptance of existing work and existing conditions. Report in writing defects in substrate which may adversely affect the performance of the foam insulation/air seal..2 Examine joints before sealing to ensure configuration, surfaces and widths are suitable for foam sealant. Report in writing the location of joints that are deemed unacceptable for the application of joint sealant. 3.3 PREPARATION.1 Ensure surfaces to receive foam insulation are free of frost, loose or foreign matter which might impair adhesion of materials..2 Prepare surface by brushing, scrubbing, scraping or grinding to remove loose mortar, loose paint, dust, oil, grease, oxidation, mill scale and other contaminants which will affect adhesion and integrity of the foam insulation/air seal system. Wipe down metal surfaces to remove release agents or other non-compatible coating, using clean sponges or rags soaked in a solvent compatible with the foam insulation. Ensure surfaces are dry before proceeding. 3.4 APPLICATION.1 Installation and surface preparation/priming shall be in accordance with membrane manufacturer s recommendations for this application..2 Apply air/vapour barrier transition membrane over clean and dry surfaces..3 Before commencing work, the Contractor will ensure that environmental and site conditions are suitable for installation of material in accordance with the insulation manufacturer s recommendation, and notify Consultant in writing of suitable surfaces and conditions.

55 École catholique St-Michel Building Envelope Upgrade Section New Liskeard, Ontario SPRAYED IN PLACE URETHANE INSULATION Project # Page 5.4 Commencement of insulation work shall imply acceptance of surfaces and conditions..5 Apply foam insulation/air seal only when surfaces and ambient temperatures are within limits prescribed by the material manufacturer..6 Apply foam insulation in strict accordance with manufacturer s written instruction, specifications or recommendations..7 Finish joints shall be free from air pockets and imbedded foreign materials. Cut back excess foam sealant after cutting flush with surrounding surfaces unless otherwise directed and/or detailed..8 Apply foam insulation to within the following tolerances: +6.4mm; -0mm of thickness indicated on drawings..9 Finished sprayed foam insulation shall be free of voids and imbedded foreign material..10 Do not allow foam insulation to cover or mark adjacent surfaces. Use masking materials if necessary..11 Remove over-spray and masking materials immediately after foam has cured to hard surface film..12 Clean and make good surfaces soiled or damaged by work of this section. Consult with section of work soiled before cleaning to ensure methods used will not damage their work..13 Damage to work of this section caused by others shall be made good by this section at the expense of those causing the damage. END OF SECTION

56 ROOM FINISH SCHEDULE - R1 Project: École Catholique St-Michel Building Envelope Upgrade Location: New Liskeard, Ontario Project No: WALL CEILING No. NAME FLOOR BASE MATERIAL FINISH MATERIAL FINISH HEIGHT REMARKS 101 Vestibule ETR New RB and ETR, See remarks New GB and ETR, See remarks Paint and ETR. See remarks ETR Contractor to provide new 16mm Type 'X' Gypsum board finish fully adhered to existing brick veneer at new metal screen location. Provide 'J' moulding around existing wall heater to remain and new meta screen framing. Provide new rubber base at the new gypsum board wall covering. Provide good finish. 102 Lobby ETR ETR ETR ETR. ETR. 103 Reception ETR ETR ETR., see remarks Paint LIT 2315mm 104 Principal ETR ETR ETR. Paint LIT 2315mm 105 Kitchenette ETR ETR ETR. Paint LIT 2315mm Existing ceiling tile to be removed from existing gypsum board fire rated ceiling assembly. Contractor to patch with new 16mm Type 'X' gypsum board c/w tape and fill and repair existing fire rated assembly to match existing. Provide remedial work at new hollow metal screen location; ensure good finish. Contractor to provide new paint finish throughout. Existing ceiling tile to be removed from existing gypsum board fire rated ceiling assembly. Contractor to patch with new 16mm Type 'X' gypsum board c/w tape and fill and repair existing fire rated assembly to match existing. Contractor to provide new paint finish throughout Existing ceiling tile to be removed from existing gypsum board fire rated ceiling assembly. Contractor to patch with new 16mm Type 'X' gypsum board c/w tape and fill and repair existing fire rated assembly to match existing. Contractor to provide new paint finish throughout Page 1

57 ROOM FINISH SCHEDULE - R1 Project: École Catholique St-Michel Building Envelope Upgrade Location: New Liskeard, Ontario Project No: WALL CEILING No. NAME FLOOR BASE MATERIAL FINISH MATERIAL FINISH HEIGHT REMARKS VCT/PT, New and See Ex. GB. 108 Classroom Remarks RB to remain Paint LIT 2680mm 109 Vestibule PT RB 110 Classroom 111 Classroom VCT/PT, See Remarks VCT/PT, See Remarks 118 Corridor ETR ETR ETR 119 Classroom 128 Classroom VCT/PT, See Remarks VCT/PT, See Remarks RB RB RB RB 129 Vestibule PT RB New and Ex. GB. to remain Paint ETR New and Ex. GB. to remain Paint ETR. New and Ex. GB. to remain Paint ETR. New and Ex. GB. to remain New and Ex. GB. to remain New GB and ETR, See remarks ETR. See remarks. ETR. See remarks. ETR. See remarks. Paint, See Remarks ETR ETR Paint Paint New GB and ETR New GB and ETR Paint new GB and ETR. See remarks. Paint new GB and ETR. See remarks. Paint and ETR. See remarks LIT 2440 For extent of VCT and Porcelain tile finish, refer to floor plan on drawing sheet 'A1.2' Modify existing LIT ceiling to suit new wall construction. For extent of Porcelain tile finish, refer to floor plan on drawing sheet 'A1.2 Modify existing LIT ceiling to suit new exterior wall construction. For extent of VCT and Porcelain tile finish, refer to floor plan on drawing sheet 'A1.2' Modify existing LIT ceiling to suit new exterior wall construction. For extent of VCT and Porcelain tile finish, refer to floor plan on drawing sheet 'A1.2' Provide remedial work at new screen 'SC02' location to match existing. Typical to both sides of wall. Modify existing LIT ceiling to suit new exterior wall construction. For extent of VCT and Porcelain tile finish, refer to floor plan on drawing sheet 'A1.2'. For GB bulkheads, refer to related wall sections. Modify existing LIT ceiling to suit new exterior wall construction. For extent of VCT and Porcelain tile finish, refer to floor plan on drawing sheet 'A1.2'. For GB bulkheads, refer to related wall sections. New gypsum board walls to receive paint finish. Existing brick veneer to remain. Provide new rubber base throughout. Page 2

58 ROOM FINISH SCHEDULE - R1 Project: École Catholique St-Michel Building Envelope Upgrade Location: New Liskeard, Ontario Project No: WALL CEILING No. NAME FLOOR BASE MATERIAL FINISH MATERIAL FINISH HEIGHT REMARKS 130 Corridor VCT VCT/PT, See 131 Classroom Remarks VCT/PT, See 132 Classroom Remarks VCT, New RB, See remarks RB RB 133 Corridor ETR ETR Paint, GB, LIT, Paint, ETR & See See LIT, See GB Remarks remarks remarks New and Ex. GB. to remain Paint LIT LIT New and Ex. GB. to remain Paint LIT LIT ETR, See remarks Paint, See Remarks ETR ETR. See remarks. See remarks Existing terrazo floor finish to remain. At new Gypsum board wall partitions, contractor to provide new rubber base as specified. Provide new paint finish at new wall partitions. For new LIT ceiling c/w bulkhead layouts, refer to Reflected Ceiling Plans on drawing sheet 'A1.6'. Provide new VCT floor finish. Extent of new VCT floor to be in line with west wall of Corridor #118. Provide good finish. For extent of VCT and Porcelain tile finish, refer to floor plan on drawing sheet 'A1.2' For extent of VCT and Porcelain tile finish, refer to floor plan on drawing sheet 'A1.2' Contractor to provide remedial work at new locker location upon removal of existing coat hooks and shelving and closet storage. Provide paint finish and rubber base at locker location to match existing. 134 Vestibule ETR ETR ETR ETR ETR ETR Page 3

59 ROOM FINISH SCHEDULE - R1 Project: École Catholique St-Michel Building Envelope Upgrade Location: New Liskeard, Ontario Project No: WALL CEILING No. NAME FLOOR BASE MATERIAL FINISH MATERIAL FINISH HEIGHT REMARKS 152 Storage Room 160 Science Classroom VCT RB 174 Storage Room VCT, see remarks RB ETR Paint ETR & GB Paint VCT, see remarks RB ETR Paint ETR, See remarks ETR, See remarks ETR, See remarks ETR ETR ETR Review and replace any damaged ceiling tiles to match existing. Remove existing paint finish down to bare concrete block where applicable using Bristle Blaster or similar. Apply one coat of latex block filler by Benjamin Moore and two (2) coats acrylic top coat by Benjamin Moore. Colour by consultant. Existing floor hatch to remain, provide VCT finish. Modifiy existing LIT ceiling to suit new gypsum board partition wall at new electrical panel. Review and replace any damaged ceiling tiles to match existing. Remove existing paint finish down to bare concrete block where applicable using Bristle Blaster or similar. Apply one coat of latex block filler by Benjamin Moore and two (2) coats acrylic top coat by Benjamin Moore. Colour by consultant. Contractor to patch existing concrete floor construction c/w metal pan and reinforcing. Provide good finish. Refer to Structural addenda No.1 Existing floor hatch to remain, provide VCT finish. Review and replace any damaged ceiling tiles to match existing. Existing finishes to remain 175 Washroom ETR ETR ETR ETR ETR ETR Page 4

60 ROOM FINISH SCHEDULE - R1 Project: École Catholique St-Michel Building Envelope Upgrade Location: New Liskeard, Ontario Project No: WALL CEILING No. NAME FLOOR BASE MATERIAL FINISH MATERIAL FINISH HEIGHT REMARKS 178 Library CT RB, see remarks ETR Paint 178a Reception CT RB ETR, GB Paint GB, See remarks GB, LIT, See Remarks Paint Paint See remarks See remarks Contractor to remove existing ceiling mounted tile. Patch at light fixture locations and other penetrations restoring existing fire rating. At vaulted ceiling location, provide skim coat to cover existing textured finish. Provide new 9.5mm type 'X' gypsum board finish c/w tape, fill and paint throughout ceiling. For extent of vaulted ceiling and bulkhead locations and bulkhead heights, refer to reflected ceiling plan on drawing sheet 'A1.6'. Contractor to provide additional 14m² of carpet tile floor finish for Owner's use. Provide new rubber base at all existing shelving and millwork to remain. At existing wood trim around vaulted ceiling, contractor to prepare wood surfaces and provide new varnish finish throughout. Contractor to remove existing ceiling mounted tile. Patch at light fixture locations restoring existing fire rating. Provide new 9.5mm type 'X' gypsum board finish c/w tape, fill and paint finish throughout ceiling. For bulkheads above library reception desk, refer to reflected ceiling plan on drawing sheet 'A1.6'. For lay-in tile ceiling height, refer to reflected ceiling plan on drawing sheet 'A1.6'. 179 Boys W.R. VCT RB GB Paint LIT 2440mm 180 Girls W.R. VCT RB GB Paint LIT 2440mm Page 5

61 ROOM FINISH SCHEDULE - R1 Project: École Catholique St-Michel Building Envelope Upgrade Location: New Liskeard, Ontario Project No: WALL CEILING No. NAME FLOOR BASE MATERIAL FINISH MATERIAL FINISH HEIGHT REMARKS 181 H.C.W.R. VCT RB GB Paint LIT 2440mm 182 Sump VCT RB GB Paint LIT 2440mm Legend ETR: Existing to remain EX: Existing CT: Carpet Tile GB: Gypsum Board PT: Porcelain Tile LIT: Lay-in Tile VCT: Vinyl Composite Tile RB: Rubber Base Page 6

62

63

64

65 ADDENDUM Project: E.c. St-Michel Building Upgrade Addendum No.: Struc01 Location: Timmins No. of Pages: 1 WSP Project # PBK: Date: 17 Mar WSP Office (Timmins) The following change(s) in the Tender Documents are effective immediately. This Addendum forms part of the Contract Documents. ITEM DESCRIPTION Related to Structural 1.01 In the science classroom, patch the existing floor opening strips under the student sinks (4 separate locations) approximately 200 x 1300mm long each using the following procedure. a) Remove all loose concrete and laitance and trim opening to obtain even surface; b) Install 10M hilti bar dowels 150mm long using HIT HY200 embed 75mm with extension spaced at 300mm 300 c/c staggered along longitudinal direction; c) Provide plywood formwork and temporary shoring at underside of floor opening as required; d) Pour 25mPa concrete to fill floor opening. Perform cast in place concrete work in accordance with CSA A23.1/A23.2. e) Clean and roughen construction joint and apply CPD latex adhesive bonding agent strictly to manufacturer s instructions. END OF STRUCTURAL ADDENDUM WSP Canada Inc. 834 Mountjoy St. South, Timmins, ON P4N 7C5 Tel: Fax:

66 1

67

68

69

70

71 ADDENDUM Project: E.c. St-Michel Building Upgrade Addendum No.: 01 Location: Timmins No. of Pages: 4 WSP Project # PBK: Date: 17 Mar WSP Office (Timmins) The following change(s) in the Tender Documents are effective immediately. This Addendum forms part of the Contract Documents. ITEM DESCRIPTION Related to ELECTRICAL, 1.01 In Classroom 108, remove two (2) duplex receptacles and provide blank cover plates in south-west corner. Four (4) new power and data receptacles will be located on the south wall as shown on SKE In Classroom 110, four (4) new power and data receptacles will be located on the north wall as shown on SKE In Classroom 111, four (4) new power and data receptacles will be located on the north wall as shown on SKE-01. Provide one (1) new duplex receptacle and one (1) data receptacle above ceiling space in the south west corner as shown on SKE In Classroom 119, four (4) new power and data receptacles will be located on the north wall as shown on SKE In Classroom 128, four (4) new power and data receptacles will be located on the south wall as shown on SKE In Classroom 131, four (4) new power and data receptacles will be located on the north wall as shown on SKE In Classroom 132, the new projector will face the south wall as shown on SKE-03. END OF ELEC ADDENDUM WSP Canada Inc. 834 Mountjoy St. South, Timmins, ON P4N 7C5 Tel: Fax: