ARCHITECTURAL SHEET INDEX MECHANICAL SHEET INDEX ELECTRICAL SHEET INDEX

Transcription

1 WILLIAMS MALL W:\48\ \Drawings\WSU BIO-SCIENCE BLDG. STEAM BOILER\Sheets\ G1.dwg, 6/22/2018 2:04:17 PM SHEET A1 M1 M2 M3 M4 M5 M6 E1 E2 ARCHITECTURAL SHEET INDEX DESCRIPTION ARCHITECTURAL GENERAL INFORMATION, PLANS & DETAILS MECHANICAL SHEET INDEX MECHANICAL GENERAL INFORMATION MECHANICAL SIXTH FLOOR - BOILER ROOM DEMOLITION PLAN MECHANICAL SIXTH FLOOR - BOILER ROOM NEW WORK PLAN MECHANICAL ROOF - DEMOLITION AND NEW WORK PLAN MECHANICAL PIPING DIAGRAMS MECHANICAL DETAILS AND SCHEDULES ELECTRICAL SHEET INDEX ELECTRICAL GENERAL INFORMATION L HANCOCK FOREST WARREN HANCOCK FOREST

2 PLAN LEGEND ABBREVIATIONS ARCHITECTURAL SHEET INDEX 22'-10 1/2" V.I.F. 7 1/4" NEW GYPSUM BOARD WALL PARTITION EXISTING DECK TO REMAIN CONT. METAL SLIP TRACK & ANCHOR, PROVIDE 16" O.C. MIN. EXTEND METAL STUD FRAMING TO DECK ABOVE EXISTING ACOUSTICAL LAY-IN CEILING TILE & GRID TO REMAIN PAINTED 5/8" GYP. BOARD ON U.O.N. 6" METAL STUD 16" O.C., PAINT TO MATCH EXISTING ADJACENT WALL PAINT, EXTEND GYP. BOARD TO DECK ABOVE, BOTH SIDES CONT. 5 1/2" MIN. SOUND ATTENUATION FIBERGLASS BATT. INSULATION, EXTEND TO DECK ABOVE CONT. METAL TRACK & ANCHOR, PROVIDE 16" O.C. MIN. BASE TO MATCH EXISTING ADJACENT WALL BASE EXISTING FINISH FLOOR SYMBOL SYMBOL DESCRIPTION WALL TO BE REMOVED NEW WALL WALL TO REMAIN LINE FOR ITEM TO BE REMOVED NEW OR RELOCATED ITEM EXISTING ITEM GENERAL SYMBOLS DESCRIPTION EXISTING COLUMN NUMBER IDENTIFICATION AND GRID SECTION IDENTIFIER DETAIL DESIGNATOR ELEVATION DESIGNATOR WORK POINT / ELEVATION ABOVE FINISHED FLOOR OR GRADE MATCH LINE BREAK LINE ROOM NUMBER IDENTIFIER DOOR NUMBER IDENTIFIER A.F.F. ALUM. ARCH. ASSY. BD. B.F. B.O.S. BOT. BRG. C.J. CLG. CLR. CLOS. C.M.U. C.O. COMM. COMP. CONC. CONSTR. CONT. CONTR. CPT. C.T. DET. DIA. D.O. DR. DWG. E.J. ELECT. EL. OR ELEV. ENG. EQ. EQUIP. E.W.C. EX. EXP. EXT. FIN. FL. OR FLR. GALV. GA. G.C. GL. GYP. HDWR. H.D.G. H.M. HORIZ. H.P. HT. INSUL. INT. JAN. JST. LAM. LAV. ABOVE FINISHED FLOOR ALUMINUM ARCHITECTURAL ASSEMBLY BOARD BARRIER FREE BOTTOM OF STEEL BOTTOM BEARING CONTROL JOINT CEILING CLEAR CLOSET CONCRETE MASONRY UNIT CLEAN OUT COMMUNICATION COMPACTED CONCRETE CONSTRUCTION CONTINUOUS CONTRACTOR CARPET CERAMIC TILE DETAIL DIAMETER DOOR OPENING DOOR DRAWING EXPANSION JOINT ELECTRICAL ELEVATION ENGINEER EQUAL EQUIPMENT ELECTRIC WATER COOLER EXISTING EXPANSION EXTERIOR FINISH FLOOR GALVANIZED GAUGE GENERAL CONTRACTOR GLASS OR GLAZING GYPSUM HARDWARE HOT-DIPPED GALVANIZED HOLLOW METAL HORIZONTAL HIGH POINT HEIGHT INSULATION INTERIOR JANITOR JOIST LAMINATE LAVATORY L.P. MANUF. MAS. MAX. MECH. MET. OR MTL. MIN. MTD. M.O. N.I.C. NON. COMB. N.T.S. O.C. O.H. OPN'G. OPP. PL. P.LAM. PT. PTD. PR. R. R.A. R.B. REINF. REQ'D. RM. R.O. S.C. S.F. SHT. SIM. S.S. ST. STL. STRUCT. SUSP. THK. THRU T.O. T.O.C. T.O. CONC. T&G T.S. T.O.S. TYP. UNEXCAV. U.O.N. V.C.T. VERT. VEST. V.I.F. W/ WD. W.P. LOW POINT MANUFACTURER MASONRY MAXIMUM MECHANICAL METAL MINIMUM MOUNTED MASONRY OPENING NOT IN CONTRACT NON COMBUSTIBLE NOT TO SCALE ON CENTER OVERHEAD OPENING OPPOSITE PLATE PLASTIC LAMINATE PAINT PAINTED PAIR RADIUS RETURN AIR RUBBER BASE REINFORCED/REINFORCING REQUIRED ROOM ROUGH OPENING SOLID CORE SQUARE FEET SHEET SIMILAR STAINLESS STEEL STONE STEEL STRUCTURAL SUSPENDED THICK THROUGH TOP OF TOP OF CURB TOP OF CONCRETE TONGUE AND GROOVE TUBE STEEL TOP OF STEEL TYPICAL UNEXCAVATED UNLESS OTHERWISE NOTED VINYL COMPOSITION TILE VERTICAL VESTIBULE VERIFY IN FIELD WITH WOOD WORK POINT SHEET A1 DESCRIPTION ARCHITECTURAL GENERAL INFORMATION, PLANS & DETAILS OVERVIEW OF ARCHITECTURAL SCOPE THIS OVERVIEW OF SCOPE IS INCLUDED TO GIVE THE CONTRACTOR A GENERAL OVERVIEW OF THE PROJECT REQUIREMENTS. THE OVERVIEW IS NOT ALL INCLUSIVE AND IS NOT INTENDED TO, AND SHOULD NOT BE USED TO, ESTABLISH CONTRACT LIMITS OR PRICING INCLUSIONS. THE CONTRACT DOCUMENTS SHALL BE USED TO ESTABLISH CONSTRUCTION CONTRACT SCOPE. THIS OVERVIEW OF SCOPE INCLUDES, BUT IS NOT LIMITED TO THE FOLLOWING: ARCHITECTURAL: 1. DEMOLITION OF WALLS, FINISH MATERIALS AND OTHER MISCELLANEOUS ARCHITECTURAL ITEMS AS INDICATED. 2. PROVIDE INTERIOR WALL SYSTEMS AS INDICATED. 3. PROVIDE INTERIOR FINISHES AS INDICATED. 4. PROVIDE ROOF MODIFICATIONS TO ROOF MEMBRANE, SUPPORT STEEL AND CURBS AS INDICATED. 5. PAINT INTERIOR WALLS AS INDICATED. PROJECT REQUIREMENTS PROVIDE ALL NECESSARY PERMITS. ALL WORK SHALL BE INSTALLED TO COMPLY WITH THE OWNER'S STANDARDS, STATE AND LOCAL CODES INCLUDING, BUT NOT LIMITED TO, THE FOLLOWING CODES AND THEIR RELATED REFERENCES MICHIGAN MECHANICAL CODE 2015 MICHIGAN PLUMBING CODE 2015 INTERNATIONAL FIRE CODE (AS REFERENCED) 2015 INTERNATIONAL FUEL GAS CODE NFPA 101 LIFE SAFETY CODE 1997 AND 2006 (AS REFERENCED) MICHIGAN ENERGY CODE-ASHRAE NATIONAL ELECTRICAL CODE AS AMENDED BY THE 2014 MICHIGAN ELECTRICAL CODE RULES, PART MICHIGAN BUILDING CODE MANUFACTURER AND MODEL NUMBER LISTED REPRESENTS THE BASIS OF DESIGN FOR THIS PROJECT. THE CONTRACTOR SHALL BEAR ALL ADDITIONAL COSTS ASSOCIATED WITH USING EQUIPMENT AND/OR SYSTEMS BY OTHER APPROVED MANUFACTURERS INCLUDING ADDITIONAL COSTS BY OTHER TRADES. ALL EQUIPMENT AND/OR SYSTEMS INSTALLED SHALL BE IN ACCORDANCE WITH THE MANUFACTURER'S RECOMMENDATIONS. WHERE FIELD OR PROJECT CONDITIONS DO NOT ALLOW ALL MANUFACTURER'S RECOMMENDATIONS TO BE MET, THE INSTALLING CONTRACTOR SHALL SUBMIT IN WRITING TO THE ARCHITECT THE PROPOSED DEVIATION, IN A SKETCH FORM, ACCOMPANIED BY THE MANUFACTURER'S CONCURRENCE. GENERAL NOTES: W:\48\ \Drawings\WSU BIO-SCIENCE BLDG. STEAM BOILER\Sheets\ A1.dwg, 6/22/2018 2:07:47 PM NEW MODIFIED BITUMEN ROOF MEMBRANE, FLASH MEMBRANE TO EX. ROOF MEMBRANE PER ROOF MFR. RECOMMENDATIONS NEW ROOF INSULATION INFILL, MATCH TYPE, THICKNESS & R-VALUE OF EXISTING ROOF INSULATION NEW ROOF DECK INFILL, MATCH THICKNESS & PROFILE OF EX. ROOF DECK, NEST NEW ROOF DECK INFILL INTO EXISTING ROOF DECK NEW INFILL EXISTING ROOF SECTION DETAIL V.I.F. EX. ROOF INSULATION V.I.F. EX. ROOF DECK EX. ROOF DECK STRUCTURAL SUPPORT ANGLE STACK DETAIL ROOF NEW WORK PLAN 6TH FLOOR NEW WORK PLAN 6TH FLOOR DEMO PLAN DEMOLITION KEYED NOTES: REMOVE EXISTING GYPSUM BOARD WALL AS INDICATED TO ALLOW FOR TURNING CLEARANCES WHILE MOVING NEW BOILER OUT OF ELEVATOR NEW WORK KEYED NOTES: INFILL EXISTING ROOF OPENING WHERE EXISTING ROOF PENETRATIONS, ROOF CURB, &/OR MECH. EQUIPMENT WAS REMOVED, REFER TO MECH. & DETAIL 5/A1 FOR ROOF INFILL MODIFY EXISTING ROOF OPENING AND CURB AS NECESSARY TO ACCEPT NEW MECH. EQUIPMENT WHERE EXISTING MECH. EQUIPMENT WAS REMOVED, REFER TO MECH. & DETAIL 4/A1 FOR MORE INFORMATION NEW GYP. BOARD WALL, REFER TO DETAIL "A" THIS SHEET FOR ADDITIONAL INFORMATION EXISTING MECH. EQUIPMENT TO REMAIN, REFER TO MECH. 1. VERIFY ALL EXISTING DIMENSIONS IN FIELD PRIOR TO CONSTRUCTION. CONTRACTORS TO NOTIFY ARCHITECT OF ANY DISCREPANCIES BETWEEN CONTRACT DOCUMENTS AND EXISTING CONDITIONS. 2. PROTECT ALL FINISH WORK TO REMAIN FROM DAMAGE DURING DEMOLITION AND CONSTRUCTION, TYPICAL. REPAIR OF DAMAGED EXISTING FINISHES WILL BE AT THE CONTRACTORS EXPENSE, TYPICAL. 3. REFER TO OTHER SHEETS OF THIS DOCUMENT SET FOR COMPLETE CONTRACT REQUIREMENTS, TYPICAL. 4. REFER TO MECHANICAL DRAWINGS FOR ADDITIONAL WORK REQUIRED. COORDINATE WORK WITH MECHANICAL CONTRACTORS. 5. REFER TO NEW WORK DRAWINGS FOR SIZES AND EXTENT OF NEW INSTALLATIONS/LAYOUTS. PROVIDE DEMOLITION AS REQUIRED TO ACCOMMODATE THE ENTIRE NEW SCOPE OF WORK AS DELINEATED IN THESE DRAWINGS. REFER TO THE COVER SHEET FOR THE COMPLETE DRAWING INDEXES. 6. PROVIDE SEPARATION BETWEEN DISSIMILAR METALS, TYPICAL. 7. MAINTAIN ALL MEANS OF EGRESS DURING CONSTRUCTION. BID 06/22/18 FINAL OWNER REVIEW 06/08/ A1 DFH DFH JSR

3 BID 06/22/18 FINAL OWNER REVIEW 06/08/18 W:\48\ \Drawings\WSU BIO-SCIENCE BLDG. STEAM BOILER\Sheets\ M1.dwg, 6/22/2018 2:01:27 PM M1

4 SHEET NOTES: 1. ANY INTERRUPTIONS OF EXISTING SERVICES AND/OR EQUIPMENT SHALL BE PERFORMED AT A TIME APPROVED IN ADVANCE BY THE OWNER'S REPRESENTATIVE SO AS NOT TO INTERFERE WITH THE PRESENT BUILDING'S OPERATION. 2. THESE DRAWINGS ARE DIAGRAMMATIC AND INDICATE THE GENERAL EXTENT OF WORK TO BE PERFORMED. THE EXACT EXTENT OF DEMOLITION SHALL BE AS REQUIRED BY THE NEW WORK. 3. ALL MECHANICAL ITEMS TO BE REMOVED SHALL BE REMOVED COMPLETE WITH ALL RELATED ITEMS INCLUDING HANGERS, SUPPORTS, CONTROLS, ETC. CAP ALL OPEN ENDED PIPES AND DUCTWORK. 4. ALL DEMOLITION OF THE EXISTING MECHANICAL SYSTEMS, INCLUDING BUT NOT LIMITED TO PIPING, DUCTWORK, CONTROLS, SUPPORTS, HANGERS, AND EQUIPMENT SHALL BE UNDER SCOPE OF DIVISION 23 OF THE SPECIFICATIONS. 5. THE OWNER SHALL HAVE FIRST RIGHT OF REFUSAL ON ALL EQUIPMENT BEING REMOVED. DEMOLITION KEYED NOTES: REMOVE AND RELOCATE EXISTING HOT WATER STORAGE TANK. REMOVE EXISTING 20"Ø WATER HEATER FLUE. REMOVE EXISTING GAS PIPING BACK TO 3" NG RISER. REMOVE EXISTING WATER HEATER, CIRCULATING PUMPS, AND ASSOCIATED CW, HW, AND HWR PIPING AS INDICATED. EXISTING SINK TO REMAIN. REMOVE CW & HW PIPING. EXISTING EYEWASH TO REMAIN. EXISTING 1-1/4" PUMPED CONDENSATE. REMOVE EXISTING DEARATOR AND BOILER FEED PUMPS. REMOVE EXISTING BLOW OFF TANK AND TEMPERATURE REGULATING VALVE. RETAIN TEMPERATURE REGULATING VALVE FOR FUTURE RELOCATION. REMOVE EXISTING 16"Ø FLUE. REMOVE EXISTING STEAM PIPING FROM GENERATOR ABOVE MEZZANINE. REMOVE EXISTING STEAM VENT THROUGH ROOF. REMOVE ABANDONED R.O. UNIT AND STORAGE TANK. REMOVE EXISTING STEAM BOILER AND ASSOCIATED PIPING AS INDICATED. REMOVE HHW PIPING AS INDICATED. REMOVE EXIST. CW, HW, AND HWR PIPING FROM WATER HEATER BACK TO VALVE. REMOVE EXIST. R.O. UNIT WATER SOFTENER AND PIPING. BID 06/22/18 FINAL OWNER REVIEW 06/08/18 W:\48\ \Drawings\WSU BIO-SCIENCE BLDG. STEAM BOILER\Sheets\ M2.dwg, 6/22/2018 2:00:46 PM MECHANICAL SIXTH FLOOR - BOILER ROOM MEZZANINE DEMOLITION PLAN MECHANICAL SIXTH FLOOR - BOILER ROOM DEMOLITION PLAN M2

5 SHEET NOTES: 1. THESE DRAWINGS ARE DIAGRAMMATIC & INDICATE THE GENERAL EXTENT OF THE WORK. PROVIDE MECHANICAL SYSTEMS COMPLETE AND PER SPECIFICATIONS, AND PER APPLICABLE CODES INCLUDING ALL NECESSARY OFFSETS, AND FITTINGS WHICH ARE REQUIRED DUE TO SPACE CONSTRAINTS OR OTHER CONDITIONS. 2. CONTRACTOR SHALL COORDINATE HIS WORK WITH THE WORK OF ALL OTHER TRADES. VERIFY ALL CLEARANCES PRIOR TO THE FABRICATION OF ANY WORK. 3. PIPING AND DUCTWORK SHALL NOT BE LOCATED OVER ELECTRICAL EQUIPMENT/PANELS. PROVIDE REQUIRED CLEARANCE IN FRONT OF ELECTRICAL EQUIPMENT. PIPING AND DUCTWORK SHALL NOT INTERFERE WITH ELECTRICAL EQUIPMENT CLEARANCE. 4. THE CONTRACTOR SHALL PROVIDE ALL MISCELLANEOUS SUPPORTING STEEL, ETC. FOR THE PROPER INSTALLATION OF ALL MECHANICAL SYSTEMS. 5. COORDINATE FLOOR, WALL, AND ROOF PENETRATIONS WITH ARCHITECTURAL TRADES. 6. COORDINATE AND PROVIDE ACCESS DOORS IN HARD CEILING AREAS FOR ACCESS TO BALANCING DAMPERS, ETC. REFER TO ARCHITECTURAL DRAWINGS FOR CEILING TYPES. 7. FOR EQUIPMENT VALVING, COMPONENT, AND PIPING ARRANGEMENT, REFER TO PIPING DIAGRAMS AND DETAILS. 8. ROUTE GAS PIPING UP THROUGH ROOF. NEW WORK KEYED NOTES: CONNECT 3" STEAM TO EXISTING 5" STEAM MAIN. REFER TO DOMESTIC WATER HEATER PIPING DIAGRAM. REMOVE SHUT OFF VALVE IN RISER. INSTALL NEW MODULATING VALVE AND REINSTALL SHUT OFF VALVE. RELOCATED DOMESTIC HOT WATER STORAGE TANK (432 GAL). BID 06/22/18 FINAL OWNER REVIEW 06/08/18 W:\48\ \Drawings\WSU BIO-SCIENCE BLDG. STEAM BOILER\Sheets\ M3.dwg, 6/22/2018 2:00:16 PM MECHANICAL SIXTH FLOOR - BOILER ROOM MEZZANINE PLAN MECHANICAL SIXTH FLOOR - BOILER ROOM PLAN M3

6 SHEET NOTES: 1. ANY INTERRUPTIONS OF EXISTING SERVICES AND/OR EQUIPMENT SHALL BE PERFORMED AT A TIME APPROVED IN ADVANCE BY THE OWNER'S REPRESENTATIVE SO AS NOT TO INTERFERE WITH THE PRESENT BUILDING'S OPERATION. 2. THESE DRAWINGS ARE DIAGRAMMATIC AND INDICATE THE GENERAL EXTENT OF WORK TO BE PERFORMED. THE EXACT EXTENT OF DEMOLITION SHALL BE AS REQUIRED BY THE NEW WORK. 3. ALL MECHANICAL ITEMS TO BE REMOVED SHALL BE REMOVED COMPLETE WITH ALL RELATED ITEMS INCLUDING HANGERS, SUPPORTS, CONTROLS, ETC. CAP ALL OPEN ENDED PIPES AND DUCTWORK. 4. ALL DEMOLITION OF THE EXISTING MECHANICAL SYSTEMS, INCLUDING BUT NOT LIMITED TO PIPING, DUCTWORK, CONTROLS, SUPPORTS, HANGERS, AND EQUIPMENT SHALL BE UNDER SCOPE OF DIVISION 23 OF THE SPECIFICATIONS. 5. THE OWNER SHALL HAVE FIRST RIGHT OF REFUSAL ON ALL EQUIPMENT BEING REMOVED. DEMOLITION KEYED NOTES: REMOVE EXISTING 16"Ø BOILER STACK. INFILL OPENING. REFER TO SHEET A1. REMOVE EXISTING 20"Ø WATER HEATER FLUE. REMOVE EXISTING RELIEF VENTS. INFILL AND PATCH ROOF. SHEET NOTES: 1. THESE DRAWINGS ARE DIAGRAMMATIC & INDICATE THE GENERAL EXTENT OF THE WORK. PROVIDE MECHANICAL SYSTEMS COMPLETE AND PER SPECIFICATIONS, AND PER APPLICABLE CODES INCLUDING ALL NECESSARY OFFSETS, AND FITTINGS WHICH ARE REQUIRED DUE TO SPACE CONSTRAINTS OR OTHER CONDITIONS. 2. CONTRACTOR SHALL COORDINATE HIS WORK WITH THE WORK OF ALL OTHER TRADES. VERIFY ALL CLEARANCES PRIOR TO THE FABRICATION OF ANY WORK. 3. PIPING AND DUCTWORK SHALL NOT BE LOCATED OVER ELECTRICAL EQUIPMENT/PANELS. PROVIDE REQUIRED CLEARANCE IN FRONT OF ELECTRICAL EQUIPMENT. PIPING AND DUCTWORK SHALL NOT INTERFERE WITH ELECTRICAL EQUIPMENT CLEARANCE. 4. THE CONTRACTOR SHALL PROVIDE ALL MISCELLANEOUS SUPPORTING STEEL, ETC. FOR THE PROPER INSTALLATION OF ALL MECHANICAL SYSTEMS. 5. COORDINATE FLOOR, WALL, AND ROOF PENETRATIONS WITH ARCHITECTURAL TRADES. 6. COORDINATE AND PROVIDE ACCESS DOORS IN HARD CEILING AREAS FOR ACCESS TO BALANCING DAMPERS, ETC. REFER TO ARCHITECTURAL DRAWINGS FOR CEILING TYPES. 7. FOR EQUIPMENT VALVING, COMPONENT, AND PIPING ARRANGEMENT, REFER TO PIPING DIAGRAMS AND DETAILS. NEW WORK KEYED NOTES: NEW 8"Ø STACK TERMINATE 7'-0" ABOVE ROOF. NEW STEAM RELIEF VENTS. BID 06/22/18 FINAL OWNER REVIEW 06/08/18 W:\48\ \Drawings\WSU BIO-SCIENCE BLDG. STEAM BOILER\Sheets\ M4.dwg, 6/22/2018 1:59:50 PM MECHANICAL ROOF - DEMOLITION PLAN MECHANICAL ROOF - NEW WORK PLAN M4

7 BID 06/22/18 FINAL OWNER REVIEW 06/08/18 W:\48\ \Drawings\WSU BIO-SCIENCE BLDG. STEAM BOILER\Sheets\ M5.dwg, 6/22/2018 1:59:13 PM M5

8 BID 06/22/18 FINAL OWNER REVIEW 06/08/18 W:\48\ \Drawings\WSU BIO-SCIENCE BLDG. STEAM BOILER\Sheets\ M6.dwg, 6/22/2018 2:07:12 PM M6

9 DEMOLITION ONE-LINE DIAGRAM NOT TO SCALE DEMOLITION KEYED NOTES: DISCONNECT, MAKE CIRCUIT SAFE AND REMOVE ELECTRICAL COMPLETE INCLUDING FUSES, DISCONNECTS, CONTROL PANELS AND ALL ASSOCIATED CONDUIT/WIRE FROM EQUIPMENT TO BE REMOVED BACK TO SWITCH/FUSE UNIT. NEW ONE-LINE DIAGRAM NOT TO SCALE W:\48\ \Drawings\WSU BIO-SCIENCE BLDG. STEAM BOILER\Sheets\ E1.dwg, 6/22/2018 2:06:21 PM BLD DSS ELECTRICAL OVERALL 6TH FLOOR PLAN E1

10 SHEET NOTES: 1. COORDINATE ALL DEMOLITION WORK WITH MECHANICAL TRADES. 2. MAINTAIN BRANCH CIRCUIT CONTINUITY TO EXISTING RECEPTACLES/EQUIPMENT THAT ARE TO REMAIN (NOT INTENDED FOR DEMOLITION, BUT INTERRUPTED BY DEMOLITION WORK). 3. PROVIDE BLANK STAINLESS STEEL COVERPLATES FOR EXISTING EMPTY OUTLET BOXES. 4. ALL 120V, 20A CIRCUITS OVER 100' IN LENGTH TO BE #10 AWG MINIMUM. 5. CIRCUIT NUMBERS SHOWN (FROM EXISTING PANELS) ARE FOR REFERENCE ONLY AND MAY NOT REFLECT THE ACTUAL POSITION OF "SPARE" BREAKERS IN EXISTING PANELS. "SPARE" CIRCUIT BREAKERS ARE THOSE THAT ARE EXISTING SPARE OR BECOME AVAILABLE DUE TO DEMOLITION IN THE AREA. DEMOLITION KEYED NOTES: ELECTRICAL SIXTH FLOOR BOILER ROOM MEZZANINE NEW WORK PLAN ELECTRICAL SIXTH FLOOR BOILER ROOM NEW WORK PLAN DISCONNECT, MAKE CIRCUIT SAFE, AND REMOVE ELECTRICAL COMPLETE FOR ELECTRIC STEAM GENERATOR INCLUDING THE DISCONNECT AND ALL CONDUIT/WIRE BACK TO THE SOURCE (SUBSTATION #2- PENTHOUSE) AND TAG SWITCH SPARE. DISCONNECT, MAKE SAFE, AND REMOVE ALL ELECTRICAL FOR R.O. UNIT COMPLETE INCLUDING CONTROL PANEL AND ASSOCIATED CONDUIT/WIRE BACK TO SOURCE (PP-5). DISCONNECT, MAKE CIRCUIT SAFE AND REMOVE COMPLETE ALL ELECTRICAL FOR BOILER FEED PUMP SYSTEM INCLUDING CONTROL PANEL AND CONDUIT/WIRE BACK TO SOURCE (PP-5). DISCONNECT, MAKE CIRCUIT SAFE AND REMOVE COMPLETE ALL ELECTRICAL FOR BOILER B-3 INCLUDING DISCONNECT, CONTROL PANEL, AND CONDUIT/WIRE BACK TO SOURCE (PP-5). DISCONNECT, MAKE SAFE AND REMOVE COMPLETE ALL ELECTRICAL FOR HOT WATER HEATER PUMPS INCLUDING STARTERS, CONTROL PANEL AND ALL CONDUIT/WIRE BACK TO SOURCE (RP16). DISCONNECT AND REMOVE ELECTRICAL FOR R.O. SOFTENER COMPLETE INCLUDING ALL CONDUIT/WIRE BACK TO SOURCE (RP16). DISCONNECT, MAKE CIRCUIT SAFE AND REMOVE COMPLETE ALL ELECTRICAL FOR BOILER B-1 INCLUDING UNIT MOUNTED DISCONNECT, CONTROL PANEL AND CONDUIT/WIRE BACK TO SOURCE (PP-5). NEW WORK KEYED NOTES: PROVIDE UNISTRUT SUPPORTS FOR MOUNTING OF STARTERS FOR PUMPS. BID 06/22/18 BLD W:\48\ \Drawings\WSU BIO-SCIENCE BLDG. STEAM BOILER\Sheets\ E2.dwg, 6/22/2018 3:14:22 PM ELECTRICAL SIXTH FLOOR BOILER ROOM MEZZANINE DEMOLITION PLAN ELECTRICAL SIXTH FLOOR BOILER ROOM DEMOLITION PLAN E2 DSS