ALL PROSPECTIVE CONTRACTORS, PLAN ROOMS AND SUPPLIERS

Transcription

1 Architect: Studio 2H Design, LLC th Avenue North, Suite 101 Birmingham, Alabama (205) July 26, 2018 ADDENDUM NO. 5 UA Project No.: EDA Investment No.: B.C. No.: S2HD Project No.: OWNER: The University of Alabama PROJECT: BID DATE: UA Economic Development Resource Center The University of Alabama 617 Greensboro Avenue Tuscaloosa, AL REVISED BID OPENING DATE: TUESDAY, JULY 31, 2018, 2:00 PM LOCAL TIME Bids to be received at UA Facilities Construction Administration th Street, Tuscaloosa, AL TO: ALL PROSPECTIVE CONTRACTORS, PLAN ROOMS AND SUPPLIERS The following changes, modification, and/or additions to the Contract Documents are hereby made part of same and are incorporated in full force as part of the Contract. This Addendum forms a part of the Contract Documents and modifies the original Construction Documents dated April 10, Bidders shall acknowledge receipt of this Addendum in the space provided on the Bid Form when submitting a bid. Failure to do so may subject the Bidder to disqualification. This Addendum shall supersede all contrary and/or conflicting information contained in the Contract Documents, which are hereby amended as follows: GENERAL: Bidders shall have access to the building for site visits on July 27 th and July 30 th from 9 am until 10 am to confirm the exact location of the existing data room. REVISIONS TO PREVIOUS ADDENDA: AD5.1 Addendum No. 4, Number AD4.37, Sheet E4.01, the sentence shown below should be added to this item. This contractor shall confirm the exact location of the existing second floor data room within the Ford Building prior to bid and all work herein described shall be as directed by UA OIT. STUDIO2HDESIGN TH Avenue North, Suite 101 Birmingham, Alabama Office: Fax:

2 Addendum No. 5 UA Economic Development Resource Center July 26, 2018 AD5.2 SECTION ALTERNATES. Replace the previously issued section with the attached two (2) page section. BID AND CONTRACT REQUIREMENTS TO BE REVISED BY ADDENDUM AD5.3 BID PROPOSAL FORM, reissued in its entirety, 3 pages. SPECIFICATIONS TO BE REVISED BY ADDENDUM AD5.4 SECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONT, 2.1 MANUFACTURERS, A. Manufacturers: subject to meeting all specification requirements including custom color and face caps, Coral Architectural Products is an approved storefront manufacturer. AD5.5 SECTION MOVEABLE WALLS, Page , 1.0 QUALITY ASSORANCE, B. Installer Qualifications. 1. Revise the word approved to certified. AD5.6 SECTION MOVEABLE WALLS, Page , 2.4 UNITIZED PANEL TYPES, B. Glazed Panels. 1. Revise subparagraph a. to: Segmented metal cladding in up to three (3) horizontal segments as per approved elevations, fit to aluminum frame. 2. Delete subparagraph b. AD5.7 SECTION HYDRAULIC ELEVATORS, Page16, 2.9 CAR ENCLOSURE - Revise this article in its entirety. 2.9 CAR ENCLOSURE A. Passenger Elevator: Provide complete car enclosure as specified herein. Provide the following features: 1. Shell: Reinforced 14-gauge furniture steel with baked enamel interior finish as selected. Apply sound-deadening mastic to exterior. 2. Canopy: Reinforced 12-gauge furniture steel with white, reflective baked enamel interior finish. Provide hinged emergency exit with shutdown contact to prevent operation of the elevator if exit is not in the closed position. 3. Swing front return panels: Swing entire unit on substantial pivot points. Locate pivot point to provide full swing of front return panel without interference with side wall finish or handrail. Secure in closed position with concealed three-point latching. Provide service cabinet with flush cover and certificate window. Hoistway face of return panel at door jamb shall be at least one inch in width to allow travel of car door beyond line of clear opening. 4. Transom: Reinforced full width of enclosure. 5. Car Door Panels: Minimum reinforced stainless steel. Same construction as hoistway door panels. Wrap any applied metal a minimum of ½ on back sides. Page 2 of 3

3 Addendum No. 5 UA Economic Development Resource Center July 26, Base: Stainless steel with concealed ventilation cutouts. 7. Interior Wall Finish/Removable Wall Panels: Stainless steel. 8. Ventilation: Morrison Products, Model AA, 3-speed Exhaust Blower with diffusor and grille mounted on rubber isolation grommets. 9. Lighting: Provide LED fixtures with wiring and hookup. 10. Suspended Ceiling: Three-section, translucent plastic panels mounted in an extruded aluminum angle and T-frame. 11. Handrails: Provide on all walls at 32" above finished floor. Return ends to wall. Handrail material shall be stainless steel. 12. Pads and Buttons: Stitched cloth pads in section, one section for each side and rear wall and one section, with cutout for faceplate, for each front return panel. Provide cutouts to access main car operating panel. This Addendum No. 5 shall be attached to the front of your set of the Project Manual - Specifications and made a part of the Contract Documents. STUDIO 2H DESIGN, LLC By Edward Griffith, Registered Architect eddie@studio2hd.com Attachments: Section Alternates 2 pages Bid Proposal Form 3 pages Page 3 of 3

4 STUDIO 2H DESIGN, LLC UA ECONOMIC DEVELOPMENT RESOURCE CENTER UA PROJECT # Page 1 of 2 SECTION ALTERNATES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes administrative and procedural requirements for alternates. 1.2 DEFINITIONS A. Alternate: An amount proposed by bidders and stated on the Bid Form for certain work defined in the Bidding Requirements that may be deducted from the Base Bid amount if Owner decides to accept a corresponding change either in the amount of construction to be completed or in the products, materials, equipment, systems, or installation methods described in the Contract Documents. 1. The credit for each alternate is the net deduction from the Contract Sum for deleting the alternate from the Work. No other adjustments are made to the Contract Sum. 1.3 PROCEDURES A. Coordination: Modify or adjust affected adjacent work as necessary to completely integrate work of the alternate into Project. 1. Include as part of each alternate, miscellaneous devices, accessory objects, and similar items incidental to or required for a complete installation whether or not indicated as part of alternate. B. Notification: Immediately following award of the Contract, notify each party involved, in writing, of the status of each alternate. Indicate if alternates have been accepted, rejected, or deferred for later consideration. Include a complete description of negotiated modifications to alternates. C. Execute accepted alternates under the same conditions as other work of the Contract. D. Schedule: A Schedule of Alternates is included at the end of this Section. Specification Sections referenced in schedule contain requirements for materials necessary to achieve the work described under each alternate. S2HD ALTERNATES

5 STUDIO 2H DESIGN, LLC UA ECONOMIC DEVELOPMENT RESOURCE CENTER UA PROJECT # Page 2 of 2 PART 2 - PRODUCTS (Not Used) PART 3 - EXECUTION 3.1 SCHEDULE OF ALTERNATES A. Alternate No. 1 Lower the height of the Moveable Wall System specified in Section The BASE BID configuration shall include: 1. 9 tall partitions. 2. Corridor Partitions at offices shall be 9 tall, 6mm clear, tempered glass (with no muntins full height). 3. Corridor Partitions at workrooms shall be painted metal panels up to 42 tall (where noted) and 6mm clear glass from 42 high to 9 (with no muntins, full height above metal). 4. Demising walls between adjacent partitioned spaces shall be 9 tall partitions with painted metal tiles. These partitions shall be divided into three vertical segments as indicated. 5. The doors shall be 7 tall 6mm clear tempered glass panels with aluminum framing with epoxy powder coated finish. Under DEDUCTIVE ALTERNATE NO. 1, the system configuration shall include: 1. 8 tall partitions in lieu of the 9 tall partitions indicated in the Base Bid. 2. Corridor Partitions at offices shall be 8 tall, 6mm clear tempered glass with no muntins. 3. Corridor Partitions at workrooms shall be painted metal panels up to 42 tall (where noted) and 6mm clear glass from 42 high to 8. No muntins at glass sections. 4. Demising walls between adjacent partitioned spaces shall be 8 tall partitions with painted metal tiles. These partitions shall be divided into three vertical segments as shown in Base Bid. 5. The doors shall be 8 tall 6mm clear tempered glass panels with aluminum framed doors with no transoms above the doors. Powder coated epoxy aluminum finish. Deductive Amount: B. Alternate No. 2 Delete mechanical window shading devices. Deductive Amount: END OF SECTION S2HD ALTERNATES

6 BID PROPOSAL FORM THE BOARD OF TRUSTEES OF THE BID PROPOSAL FOR: UNIVERSITY OF ALABAMA The University of Alabama c/o Construction Administration Economic Development Resource Center P.O. Box Greensboro Avenue th Street Tuscaloosa, Alabama Tuscaloosa, Alabama UA Project No EDA Investment No The Undersigned, as Bidder, hereby declares that the only person or persons interested in the Proposal as Principals is or are as herein named and that no other person than herein named has any interest in this Proposal or in the Contract to be entered into; that this Proposal is made without connection with any other person, company, or parties making a bid or proposal; and that it is in all respects fair and in good faith without collusion or fraud. The Bidder further declares that he has examined the site of the work, and informed himself fully in regard to all conditions pertaining to the place where the work is to be done, and that he has examined the Drawings and Specifications, including Addenda Nos. for the work and the other Contract Documents relative thereto, and that he has satisfied himself relative to the work to be performed. The Bidder certifies by submitting this bid that they are in full compliance with the Code of Alabama, Section and and agrees to provide domestic products if the same are available at reasonable and competitive prices. The Bidder further certifies and agrees that if foreign made materials prices have been used as the basis of the bid because domestic products are not available at a reasonable and competitive price, there has been a downward adjustment in contract price equal to any realized savings or benefit to the Bidder and the foreign materials utilized are of an equal or greater quality. The Bidder certifies by submitting this bid that they are in full compliance with State of Alabama Act No , that they are not barred from bidding or entering into a contract pursuant to Section , Code of Alabama 1975, and that they acknowledge that the Awarding Authority may declare the bid and/or contract void if the certification is false. The Bidder further declares that he is aware of the tax exempt status of the Owner and that sales/use/severance taxes are excluded from the amount of the bid. The Owner may elect to enter into a Purchasing Agent Agreement as described in the Contract Documents. In compliance with your Advertisement for Bids dated and subject to all the conditions thereof, the undersigned Alabama General Contractor s License # Classification, A corporation organized and existing under the Laws of the State of. A Partnership consisting of Or an Individual trading as of the City of Hereby proposed to furnish all labor and materials and perform all work required for the construction of in accordance with Drawings and Specifications.

7 UNIVERSITY OF ALABAMA BID PROPOSAL Page 2 of 3 BASE BID: For construction complete as shown and specified, the sum of Dollars ($ ) ESTIMATED SALES TAX BASE BID: $ ALTERNATES: See Specifications including Section ALTERNATES DEDUCTIVE ALTERNATE NO. 1 Lower the height of the Moveable Wall System specified in Section For construction compete as shown and specified, deduct the sum of Dollars ($ ) ESTIMATED SALES TAX ALTERNATE NO. 1: $ DEDUCTIVE ALTERNATE NO. 2 Delete mechanical window shading devices: For construction complete as shown and specified, deduct the sum of Dollars ($ ) ESTIMATED SALES TAX ALTERNATE NO. 2: $ INFORMATIONAL PRICING: For the purposes of allocating funding sources, provide total base bid amounts including General Contractor s overhead and profit assigned to these categories of Work, as indicated below. This information is for internal accounting purposes and will not be used to determine the low bidder. 1. Asbestos Abatement (Roof): Provide the cost of all demolition of the roof and asbestos abatement in the roof, including the cost of any temporary roofing necessary for abatement/demolition. Do not include the cost of any temporary roofing intended to protect the existing building or construction $ 2. Asbestos Abatement (All Other) and Lead-Based Paint Removal/Encapsulation: Provide the cost of asbestos abatement in all areas other than the roof and the removal and/or encapsulation of lead-based paint throughout the building... $ 04/17

8 UNIVERSITY OF ALABAMA BID PROPOSAL Page 3 of 3 To be filled out if certified check accompanies bid: The undersigned further agrees that in case of failure on his part to execute the Contract Agreement and required Contract Bonds within fifteen (15) consecutive calendar days after being given written notice of the Award of the Contract, the check accompanying this Bid and the monies thereon shall be paid into the funds of THE BOARD OF TRUSTEES OF THE UNIVERSITY OF ALABAMA, a corporation as liquidated damages for such failure; otherwise the check accompanying this Proposal shall be returned to the undersigned. Attached hereto is a certified check on the (Institution Name) for the sum of Dollars ($ ). To be filled out if bidder s bond accompanies bid: The undersigned further agrees that in case of failure on his part to execute the Contract and Required Contract Bonds within fifteen (15) consecutive calendar days after being given written Notice of the award of the Contract, the Bidder s Bond accompanying this Bid is callable and the Surety will be called upon the Owner(s) for the liquidation; otherwise said Bidder s Bond shall be returned to the undersigned. Attached hereto is a bidder s bond of (Bonding Company) for the sum of Dollars ($ ) made payable to THE BOARD OF TRUSTEES OF THE UNIVERSITY OF ALABAMA, a corporation. The full names and residences of persons and firms submitting the bid as Principles are as follows: (must be signed to be a valid bid proposal) Signature of Bidder Date: Title Business Address 04/17